Advertisement
2. INTRODUCTION & SPECIFICATION
A totally dry heat, no condensation, no gas, no fumes and no smell. Reaches maximum heat output within seconds of being turned on. Highly polished
aluminium reflector for maximum heat efficiency. Adjusts horizontally through 25° while mounted. Controlled by push on/off switch or remote control,
allowing unit to be on full, half or low power. IWMH1809LR features two banks of 20 LED's for added lighting in evenings and dark areas. Ideal for
industrial or domestic applications. Suitable for indoor and outdoor use, if weather protected (IP24 rated).
Model No
Power:
Input supply:
Dimensions (W x H x D):
650 x 200 x 240mm
Minimum Height:
LED Quantity:
3. MOUNTING INSTALLATION
3.1
WALL MOUNTING (fig.1).
IMPORTANT! The heater should always have a minimum
clearance of 30cm from a ceiling and at least 1m from any
object. Ensure that mounting surface is capable of supporting the
weight of the heater.
3.2
Using wall bracket (2) as a template, drill the wall and insert
suitable wall fixings. NOTE: Minimum height for lower fixing
screws 1600mm.
3.3
Secure the metal bracket to the wall using screws (3).
3.4
Attach heater support (5) to the wall bracket (2) using screw (6),
washers (7) and nut (8).
3.5
Slide the heater (1B) onto the heater support (5A) and secure
using screw (9).
3.6
Adjust the angle of heater to direct heat where required.
4. OPERATION
WARNING! Ensure you read, understand and apply the safety instructions in Section 1 before using the heater.
4.1
Ensure the heater is at least 1m from any object. The heater can be tilted from 0° to 25°, set it to the required angle before switching the
heater on.
4.2
Plug in the heater and switch it on using the ON/OFF Heat button on the base of the heater, a blue indicator light will flash indicating that
the unit is in stand by mode. Press either the ON/OFF button on the control panel or on the remote to turn the heater on, the blue indicator
light will be on.
4.3
On models fitted with LED lights, switch on the lights by using the ON/OFF Light button on the base of the unit, a blue indicator light will
flash indicating that the unit is in stand by mode press the button again or the button on the remote to switch on the LED's, the blue
indicator light will be on.
4.4
When the heater or lights are no longer required, switch off using the appropriate ON/OFF button(s) on the base and unplug the unit.
NOTE: When switching off using the remote, the heater and lights will be in stand by mode.
5. MAINTENANCE
5.1
Make sure the heater plug is disconnected from the mains supply before any cleaning is attempted. Also allow the heater to cool
completely. DO NOT use water or other liquids, or harsh abrasive cleaners to clean the heater. DO NOT touch the carbon fibre elements
with fingers as this may damage the tube.
5.2
Clean the exterior with a soft damp cloth with some mild detergent.
5.3
To replace any of the elements or lamps, contact your authorised
Sealey dealer.
5.4
To change the remote batteries, press down and push back the
battery cover (fig.2), remove old batteries and replace with two
new AAA batteries.
WARNING! DO NOT mix old and new batteries and dispose of
old batteries in accordance with local authority regulations.
Declaration of Conformity
standards and directives.
CARBON FIBRE WALL hEATER
Models: IWMh1809R / IWMh1809LR
2006/95/EC Low Voltage Directive
2004/108/EC EMC Directive
93/68/EEC Marking Directive
2002/95/EC RoHS Directive
2002/96/EC WEEE Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
IWMH1809R
IWMH1809LR
1800W
1800W
230V 50Hz 13A
230V 50Hz 13A
890 x 200 x 240mm
1800mm
1800mm
-
40
We, the sole importer into the UK, declare that the product listed here is in conformity with the following
The construction file for this product is held by the Manufacturer and may be inspected, by
a national authority, upon request to Jack Sealey Ltd.
Signed by Mark Sweetman
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products.
Sole U.K. Distributor
Sealey Group
Bury St. Edmunds
Suffolk.
fig.2
15th April 2009
01284 757500
Web
01284 703534
IWMH1809R / IWMH1809LR
fig.1
www.sealey.co.uk
sales@sealey.co.uk
Issue No: 2 - 21/05/09
Advertisement
