EVM440 NON-CONTACT INFRARED THERMOMETER WITH LASER CONTACTVRIJE IR-THERMOMETER MET LASERPOINTER THERMOMÈTRE IR SANS CONTACT AVEC POINTEUR LASER TERMÓMETRO IR DE BOLSILLO CON PUNTERO LÁSER INFRAROT-THERMOMETER MIT LASERPOINTER TERMÓMETRO COM INFRAVERMELHOS E LASER USER MANUAL GEBRUIKERSHANDLEIDING MODE D'EMPLOI MANUAL DEL USUARIO...
If in doubt, contact your local waste disposal authorities. Thank you for choosing Perel! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, don't install or use it and contact your dealer.
Page 3
EVM440 • Familiarise yourself with the functions of the device before actually using it. All modifications of the device are forbidden for safety reasons. • Only use the device for its intended purpose. Using the device in an unauthorised way will void the •...
Page 4
EVM440 Push the Laser button to switch the laser pointer ON. The laser pointer is only used for aiming. When the laser is on, the laser icon appears appear on the LCD. Aim the red beam approximately 1 cm below the point of test.
Page 5
EVM440 auto switching-off and data hold 7 seconds distance-to-spot ratio D:S 12:1 power supply 1 x 9 V (not incl.) dimensions 48.8 x 133 x 146 mm weight 130 g without battery Use this device with original accessories only. Velleman nv cannot be held responsible in the event of damage or injury resulting from (incorrect) use of this device.
EVM440 GEBRUIKERSHANDLEIDING Inleiding Aan alle ingezetenen van de Europese Unie Belangrijke milieu-informatie betreffende dit product Dit symbool op het toestel of de verpakking geeft aan dat, als het na zijn levenscyclus wordt weggeworpen, dit toestel schade kan toebrengen aan het milieu. Gooi dit toestel (en eventuele batterijen) niet bij het gewone huishoudelijke afval;...
Page 7
EVM440 • Gebruik enkel geschikte batterijen (zie 'Technische Specificaties'). Bescherm tegen schokken. Vermijd brute kracht tijdens de bediening. • Bescherm het toestel tegen extreme hitte (zie 'Technische Specificaties'), stof en vochtigheid • Leer eerst de functies van het toestel kennen voor u het gaat gebruiken.
Page 8
EVM440 2. Houd de meetknop ingedrukt om de meter te activeren en begin te meten. De display licht op als de batterijspanning voldoende is. 3. Tijdens het meten kunt u: De laserknop indrukken om de laser in te schakelen. De laserstraal dient enkel als richthulp. Wanneer de laser ingeschakeld is, verschijnt het lasersymbool op de display.
Page 9
Gebruik dit toestel enkel met originele accessoires. Velleman nv is niet aansprakelijk voor schade of kwetsuren bij (verkeerd) gebruik van dit toestel. Voor meer informatie over dit product en de laatste versie van deze handleiding, zie www.perel.eu. De informatie in deze handleiding kan te allen tijde worden gewijzigd zonder voorafgaande kennisgeving.
EVM440 MODE D'EMPLOI Introduction Aux résidents de l'Union européenne Informations environnementales importantes concernant ce produit Ce symbole sur l'appareil ou l'emballage indique que l'élimination d'un appareil en fin de vie peut polluer l'environnement. Ne pas jeter un appareil électrique ou électronique (et des piles éventuelles) parmi les déchets municipaux non sujets au tri sélectif;...
Page 11
EVM440 • N'utiliser que des piles appropriées (voir 'Spécifications techniques'). Protéger l’appareil des chocs. Traiter l'appareil avec circonspection pendant l’opération. • Protéger l'appareil contre les températures extrêmes (voir 'Spécifications techniques'), la poussière et • l'humidité. • Se familiariser avec le fonctionnement de l'appareil avant de l'utiliser.
Page 12
EVM440 2. Maintenir le bouton de mesure enfoncé pour allumer le mètre et commencer à mesurer. L'afficheur s'allumera si la pile est en bon état. 3. Pendant la mesure de la température, il est possible de : Appuyer sur le bouton du laser pour allumer le laser. Le pointeur laser est seulement utilisé pour pointer.
Page 13
Pour plus d’informations concernant cet article et la dernière version de ce mode d'emploi, visiter notre site web www.perel.eu. Les spécifications et le contenu de ce mode d'emploi peuvent être modifiés sans avis préalable.
Si tiene dudas, contacte con las autoridades locales para residuos. ¡Gracias por elegir Perel! Lea atentamente las instrucciones del manual antes de usar el aparato. Si el aparato ha sufrido algún daño en el transporte no lo instale y póngase en contacto con su distribuidor.
Page 15
EVM440 • No agite el aparato. Evite usar excesiva fuerza durante el manejo y la instalación. No exponga el aparato a temperaturas extremas, polvo ni humedad (véase « Especificaciones»). • Familiarícese con el funcionamiento del aparato antes de utilizarlo. •...
Page 16
EVM440 3. Durante la medición de la temperatura, puede: Pulsar el botón láser para activar el láser. El láser sólo se utiliza sólo para apuntar. Si el láser está activado, el icono del láser activado aparece en la pantalla LCD. Apunte el rayo rojo aproximadamente 1 cm por debajo del punto de la prueba.
Page 17
(indebido) de este aparato. Para más información sobre este producto y la versión más reciente de este manual del usuario, visite nuestra página www.perel.eu. Se pueden modificar las especificaciones y el contenido de este manual sin previo aviso.
Umweltvorschriften. Falls Zweifel bestehen, wenden Sie sich für Entsorgungsrichtlinien an Ihre örtliche Behörde. Vielen Dank, dass Sie sich für Perel entschieden haben! Lesen Sie diese Bedienungsanleitung vor Inbetriebnahme sorgfältig durch. Überprüfen Sie, ob Transportschäden vorliegen. Sollte dies der Fall sein, verwenden Sie das Gerät nicht und wenden Sie sich an Ihren Händler.
Page 19
EVM440 Allgemeine Richtlinien Siehe Velleman® Service- und Qualitätsgarantie am Ende dieser Bedienungsanleitung. Betreiben Sie das Gerät nur mit dem geeigneten Batterien (siehe « Technische Daten »). • Vermeiden Sie Erschütterungen. Wenden Sie bei der Bedienung keine Gewalt an. • Schützen Sie das Gerät vor extremen Temperaturen, Staub und Feuchtigkeit (siehe « Technische Daten »).
Page 20
EVM440 Bedienung 1. Halten Sie das Gerät am Griff und richten Sie auf die zu messende Oberfläche. Für mehr Informationen, siehe ‘Abstand-zu-Punktgröße‘. 2. Halten Sie die Messtaste gedrückt, um das Gerät einzuschalten und beginnen Sie zu messen. Das Display leuchtet wenn die Batterie geladen ist.
Need help?
Do you have a question about the EVM440 and is the answer not in the manual?
Questions and answers