Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Baumann 440E
- Page 1 BAUMAN MANUFACTURING 440E/440H DROP SPREADER OPERATOR’S MANUAL...
- Page 2 MODEL: SERIAL NUMBER: PURCHASE DATE: DEALER/WHERE PURCHASED: DOCUMENT REVISION: DECEMBER 2018 3 INDUSTRIAL DRIVE ELMIRA, ON N3B 2S1 PHONE: (519)669-4333 FAX: (519)669-2431 WWW.BAUMANMFG.COM...
-
Page 3: Table Of Contents
ATTACHMENT OF THE MACHINE ............................6 SPREADING MATERIAL ................................7 HYDRAULIC/ELECTRICAL ROUTING INSTRUCTIONS ........................ 7 440E/440H, COMMON PARTS LIST ............................8 440E, ELECTRIC SPECIFIC PARTS LIST ............................9 440H, HYDRAULIC SPECIFIC PARTS LIST ..........................9 INSTALLATION LOCATIONS ..............................10 HYDRAULIC COMPONENTS ASSEMBLY ..........................14 ELECTRICAL HOOK-UP DIAGRAM ............................ -
Page 4: Introduction
INTRODUCTION Congratulations on your purchase of a Bauman Drop Spreader! This spreader has been designed and manufactured to enable operators to carry out their work safely and efficiently. The Bauman Drop Spreader is capable of spreading sand, salt, grit, or similar materials and should only be used for this purpose. -
Page 5: General Information
GENERAL INFORMATION The operator must read and understand the information in this manual to ensure the correct service and operation of the machine and avoid unnecessary risk of accidents and breakdowns. Please Note: Stop the tractor engine before you adjust, lubricate, or repair the machine. Remember to remove the ignition key to make sure no one starts the tractor while you are repairing the machine. -
Page 6: Safety Instructions
SAFETY INSTRUCTIONS This machine demands skilled operation therefore, you must read this operator’s manual before connecting the machine to the tractor. Even though you may have owned or operated similar equipment, you should read through the safety and maintenance procedures thoroughly. -
Page 7: Safety Labels
▪ Use only original components or replacement components received from Bauman Manufacturing. ▪ Sitting, reaching into or climbing on or in the spreader during operation can result in serious injury or death. Do not ride on the spreader while the vehicle is in motion. ▪... -
Page 8: Maintenance
MAINTENANCE Warning: When repairing, maintaining and cleaning the machine, it is particularly important to be aware of the safety precautions. Park the tractor (if connected) as a precautionary measure and disconnect power when servicing. Do not clean, lubricate or adjust the machine before the tractor engine has been stopped and the parking brake is activated. -
Page 9: Spreading Material
SPREADING MATERIAL REGULATING SPREAD QUANTITY The spreading quantity is adjusted with the tension adjustment lever. Correct adjustment is important. If the adjustment is too tight, unnecessary wear of the rubber belts or rotating parts may occur. If the adjustment is too slack, distribution of material will be uneven. Hydraulic Units: All hydraulic units are equipped with hydraulic flow control. -
Page 10: 440E/440H, Common Parts List
440E/440H, COMMON PARTS LIST ITEM PART NUMBER DESCRIPTION QTY. 440 410 #40 ROLLER CHAIN WITH C/LINK - DRIVE 40B30 100 #40-30 TOOTH 1" BORE 1040SI 430 BEARING PLATE 1140 201 SEAL SHIELD RUBBER SEAL 1140 201 SHIELD 1140 301 FINGER BAR ASSEMBLY... -
Page 11: 440E, Electric Specific Parts List
440E, ELECTRIC SPECIFIC PARTS LIST ITEM PART NUMBER DESCRIPTION QTY. 440 ELECTRIC DRIVE ASM SEE COMPONENTS BELOW, COMES ASSEMBLED W/ HARDWARE 29.1 1801 440 MOTOR 1/4 HP 12VDC MOTOR 29.2 1801 440 REDUCER REDUCER 35.5:1 DECAL 440E MODEL # FOR 440E 40B12 010 EXT #40-12 TOOTH 5/8"... -
Page 12: Installation Locations
INSTALLATION LOCATIONS... -
Page 16: Hydraulic Components Assembly
HYDRAULIC COMPONENTS ASSEMBLY... -
Page 17: Electrical Hook-Up Diagram
ELECTRICAL HOOK-UP DIAGRAM... -
Page 18: Optional Brackets
OPTIONAL BRACKETS 3 POINT HITCH BRACKET Part Number: Bracket 3 PT VENTRAC BRACKET Part Number: Bracket 4100 CLICK-N-GO BRACKET Part Number: Bracket CNG STEINER BRACKET Part Number: Bracket 440... -
Page 19: Additional Options
ADDITIONAL OPTIONS GALVANIZED METAL LID Part Number: 440 LID SOFT COVER Part Number: 440 COVER CONTROL BLOCK: VARIABLE POWER Part Number: 1801 440 80A-SC... -
Page 20: Warranty Information
WARRANTY INFORMATION One Year Limited Warranty If the unit fails to operate within one year from date of purchase because of defects in materials or workmanship, Bauman Manufacturing will, at its option, either replace or repair such components for the original purchaser. This warranty does not cover damage resulting from accident, misuse or abuse, water, tampering, servicing performed or attempted by unauthorized agencies, or units that have been modified in any fashion. -
Page 21: Notes
NOTES:...
Need help?
Do you have a question about the 440E and is the answer not in the manual?
Questions and answers