Halco ProLED Vapor Tight Series Installation Manual

ProLED Vapor Tight Series
®
Installation Guide
V apor Tight Series Installa�on Guide
V apor Tight Series Installa�on Guide
SAFETY INSTRUCTIONS:Read instruc�ons carefully before a�emp�ng to install fixture.
All wiring should be performed by a qualified electrician.
SAFETY INSTRUCTIONS:Read instruc�ons carefully before a�emp�ng to install fixture. Disconnect power before installing or servicing. This fixture must be wired in accordance with the Na�onal Electrical
Code and applicable local codes and ordinances.
All wiring should be performed by a qualified electrician.
●
Disconnect power before installing or servicing. This fixture must be wired in accordance with the Na�onal Electrical
●
CAUTION: Risk of file
Code and applicable local codes and ordinances.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
CAUTION: Risk of file
WARNING: Do NOT handle energized fixture when hands are wet, when standing on wet or damp surfaces or in
water.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
●
WARNING: Fixture to be independently supported to building structure.
WARNING: Do NOT handle energized fixture when hands are wet, when standing on wet or damp surfaces or in
●
water.
CLEANING&MAINTENANCE:
WARNING: Fixture to be independently supported to building structure.
●
CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.
CLEANING&MAINTENANCE:
1. Clean lens with non-abrasive cleaning solu�on.
CAUTION: Be sure the fixture temperature is cool enough to touch. Do NOT clean or maintain while the fixture is energized.
2. Do NOT open fixture to clean the LED. Do NOT touch the LED.
1. Clean lens with non-abrasive cleaning solu�on.
Note: These instruc�ons do not cover all details or varia�on in equipment, nor do they provide for every possible situa�on during
2. Do NOT open fixture to clean the LED. Do NOT touch the LED.
installa�on, opera�on or maintenance.
Note: These instruc�ons do not cover all details or varia�on in equipment, nor do they provide for every possible situa�on during
TROUBLESHOOTING:
installa�on, opera�on or maintenance.
1. Check that the line voltage at fixture is correct. Refer to wiring direc�ons.
TROUBLESHOOTING:
2. Check that the fixture is grounded properly.
1. Check that the line voltage at fixture is correct. Refer to wiring direc�ons.
2. Check that the fixture is grounded properly.
0-10V DIMMABLE WIRING:
Universal voltage driver permits opera�on at 120V through 277V, 50/60Hz.
0-10V DIMMABLE WIRING:
1. Connect the BLACK fixture lead to the (+) LINE supply lead.
Universal voltage driver permits opera�on at 120V through 277V, 50/60Hz.
2. Connect the WHITE fixture lead to the (-) COMMON supply lead
1. Connect the BLACK fixture lead to the (+) LINE supply lead.
3. Connect the GROUND wire from fixture to the supply ground. Do NOT connect the GROUND of the dimming fixture
2. Connect the WHITE fixture lead to the (-) COMMON supply lead
to the output.
3. Connect the GROUND wire from fixture to the supply ground. Do NOT connect the GROUND of the dimming fixture
4. Connect the VIOLET fixture lead to the (V+) DIM lead.
to the output.
5. Connect the GRAY fixture lead to the (V-) DIM lead.
4. Connect the VIOLET fixture lead to the (V+) DIM lead.
5. Connect the GRAY fixture lead to the (V-) DIM lead.
Halco Lighting Technologies | 2940 Pacific Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone 770.242.3612 | Fax 800.880.0822 | halcolighting.com | Atlanta | Chicago | Cleveland | Houston | Los Angeles | Phoenix
© 2020 Halco Lighting Technologies, LLC. All rights reserved. Halco is a registered trademark of Halco Lighting Technologies. All sizes and specifications are subject to change.
®