Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Nolangroup N-Com B601 X Series
- Page 2 USER INSTRUCTIONS AND SAFETY Congratulations on your purchase of an N-Com product. N-Com B601 was made using the most advanced technology and top-quality materials. Long-running tests and thorough system development have made it possible to achieve the highest audio quality. For additional information on the B601, to download the instructions in PDF format and install the latest available Firmware version, please visit the website www.n-com.it Firmware Version: 1.0.1...
-
Page 3: Table Of Contents
Contents WARNINGS AND SAFETY ........................4 1.1.Road safety ..................................4 1.2.Switching on the system in safe environments ....................... 4 1.3.Interferences ..................................4 1.4.Appropriate use ................................. 4 1.5.Qualified personnel ................................5 1.6.Accessories and batteries ............................... 5 1.7.Disposal ....................................5 CONTENT OF THE PACKAGING ......................6 INSTALLATION ON THE X-1005 AND X-903 HELMET .............. -
Page 4: Warnings And Safety
WARNINGS AND SAFETY Read this User Manual carefully, as well as the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. Caution: The product cannot be used in official or non-official competitions, motordromes, circuits, racing tracks and the like. -
Page 5: Qualified Personnel
1.6. Accessories and batteries • Only use the type of batteries, battery chargers and accessories approved by Nolangroup for the specific model. • Using a battery type different from the recommended one may lead to dangerous situations and invalidate the warranty. -
Page 6: Content Of The Packaging
CONTENT OF THE PACKAGING The N-Com B601 package contains: e-box with wiring Microphone Microphone for helmet X-903 Rechargeable battery Adesive Keypad Mini USB jack wire Flat head tool Microphone foam Key, Screw, Microphone securing Microphone securing Adhesive strips clip stickers for loudspeakers... -
Page 7: Installation On The X-1005 And X-903 Helmet
INSTALLATION ON THE X-1005 AND X-903 HELMET EASYFIT The X-1005 and X-903 helmets are pre-set for the simplified installation of the N-Com system. Important: Prior to installing the N-Com system, it is recommended to write down the identification code affixed to the product (see chapter 18.4). The installation video can be seen at www.n-com.it / Support section. - Page 8 N.B.: Make sure you do not glue the keypad flex underneath the keypad support. N.B.: In the event that the keypad is not positioned correctly, peel it off right away with extreme care and repeat the positioning. N.B.: It takes up to 24 hours for the keypad to stick completely. During this time, do not expose the helmet to atmospheric agents.
-
Page 9: Microphone Positioning
3.3. Microphone positioning ONLY FOR X-1005 HELMETS • With the help of the flat head tool supplied as standard equipment, open the microphone-holder clip located on the right side of the helmet (Fig. 14-15). • Position the microphone at the desired length, sliding the excess portion inside the cheek pad lining (Fig. -
Page 10: Repositioning The Padding
• Hook up the microphone to the connector coming out of the e-Box (Fig. 20). • Position the wiring and the connectors behind the cheek pad lining, lifting it with the help of a flat head tool (Fig. 21). Fig. 20 Fig. -
Page 11: Installation On The X-Lite Helmets
INSTALLATION ON THE X-LITE HELMETS This procedure must be followed for the installation of N-Com systems on X-lite helmets other than model X-1005 and X-903. Important: Prior to installing the N-Com system, it is recommended to write down the identification code affixed to the product (see chapter 18.4). - Page 12 ONLY FOR X-702 HELMETS • Cut along the pre-cut lines of the plastic tab on the back of the comfort padding. • Position the wiring underneath the plastic tab (Fig. 31). Fig. 31 Fig. 32 • Remove the small N-Com cap positioned on the left side of the helmet. To make the operation easier, we recommend pushing the cap from inside the helmet (Fig.
-
Page 13: Microphone Positioning
• Line up the keypad flex connector to the e-box making sure that the letter “n” is pointing as shown in Fig. 37. • Gently position the connector in its seat until it is all the way in (Fig. 38). •... -
Page 14: Repositioning The Padding
N.B.: On certain helmets, the housing for the microphone rod must be created by cutting out the helmet border gasket along the pre-cut area. FULL-FACE HELMETS • Take the polystyrene check pad (left side) and position the microphone in the special housing, as illustrated in Fig. -
Page 15: Removing The System
REMOVING THE SYSTEM To remove the system from the helmet, proceed as for the installation, by removing the various parts. Important: to remove the keypad, proceed as follows. • Remove the keypad from the helmet shell (Fig. 48). • Remove the Flex of the keypad from the connector found on the e-box (Fig. 49). •... -
Page 16: Basic Functions
BASIC FUNCTIONS Note: Before using the N-Com device for the first time, recharge the battery completely for at least 10 hours. To obtain best performances from the battery, it is recommended to completely recharge the battery the first few times. Afterwards, you can recharge the battery for shorter periods. Whenever possible, it is best to recharge the battery completely. -
Page 17: Configuration Menu
CONFIGURATION MENU All Bluetooth pair ups and other adjustments are carried out in this mode. To put the system in “Configuration mode” (starting from a switched off system) press the “n” key and keep it pressed for 4 seconds, until you hear the voice announcement “ Configuration Menu ”. -
Page 18: Mobile Phone
MOBILE PHONE To pair up a mobile phone to the B601 system, follow the procedure illustrated in Chapter 8. Answering a phone call Briefly press any key when you hear the incoming call signal. When you hear the ringtone, say any word out loud. You can enable / disable the “VOX phone”... -
Page 19: Conference Call Function
9.2. Conference call function When a call comes in on a mobile phone connected via Bluetooth to B601, the intercom is temporarily turned off. However, if you wish to share the phone call with the other helmet, simply turn on the intercom manually during the phone call. During the phone call, briefly press “n”... -
Page 20: Music Via Bluetooth
12. MUSIC VIA BLUETOOTH To pair up an Mp3 device to the B601 system, follow the procedure illustrated in Chapter 8. Play music (Play) Press “” and keep it pressed for about 2 seconds. Pause function (Pause) When the player is playing music, press “” for about 2 seconds. Next track (Skip) When the player is playing music, press “”... -
Page 21: N-Com Intercom
14. N-COM INTERCOM The N-Com B601 system allows communication with other N-Com systems, up to a maximum distance of about 150 m (in open field, with no obstacles). The range of the communication varies depending on the N-Com systems used. Important: The procedure described below refers exclusively to the pairing up and operation between the B601 and the “900”... -
Page 22: Universal Intercom" Intercom
15. “UNIVERSAL INTERCOM” INTERCOM The N-Com B601 system can be connected via Bluetooth to intercom systems of other brands or to N-Com systems other than the “900” / “600” series , thanks to the UNIVERSAL INTERCOM function. Important: N-Com systems other than the “900” / “600” series must be paired up to the N-Com B601 by following the procedure “Pairing up the Universal Intercom”. -
Page 23: Battery And Recharge
16. BATTERY AND RECHARGE 16.1. Low battery signal During its operation, the system alerts the user with a voice message when the battery is low. From the first message, the system has a 1-hour autonomy. Warning is given every 10 minute. 16.2. -
Page 24: Summary Table Of Controls
17. SUMMARY TABLE OF CONTROLS Turning on 2 sec Turning off 6 sec Increase Volume Decrease Volume Answer phone call* Voice call 2 sec Speed Dialling Menu** Hang up/reject a phone call 2 sec Manual Device Connection 2 sec Phone Conference Activation CHANNEL 1... -
Page 25: Warranty
Exclusions and limitations of coverage This warranty covers only defects in materials and workmanship. Nolangroup cannot be held liable for product defects attributable in whole or in part to any other cause, including but not limited to: • Defects or damage resulting from use of the Product in conditions other than the usual ones. -
Page 26: Product Identification
Only for repairs or replacements of electronic components, if Nolangroup repairs or replaces the product, the product will have a warranty period equal to the remaining part of the original warranty or ninety (90) days from the date of repair (whichever is longer). -
Page 27: Validity Of N-Com Warranty
18.5. Validity of N-Com warranty VALIDITY VALIDITY VALIDITY VALIDITY NATION NATION 2 YEARS 1 YEAR 2 YEARS 1 YEAR ALBANIA LEBANON ALGERIA MACEDONIA SAUDI ARABIA MALAYSIA ARGENTINA MALTA AUSTRALIA MOROCCO AUSTRIA MAURITIUS BAHRAIN MEXICO BELGIUM BRP MONTENEGRO BERMUDA NORWAY BOLIVIA NEW CALEDONIA BOSNIA-HERZEGOVINA NEW ZEALAND... - Page 28 www.n-com.it...