Related Manuals for Proluxe Endurance X1M
Summary of Contents for Proluxe Endurance X1M
- Page 1 Operations Manual Endurance X1M Manual Dough Press w/ Mold - Model #: DP1100M WWW.PROLUXE.COM Version: 122820...
- Page 2 (2.5 sq. mm) shall be used. Make sure there is a proper electrical wall outlet located the Endurance X1M Manual Dough within reach of the cord and plug attached to Press with Mold Insert. Proluxe is a the press. leading manufacturer of food ...
-
Page 3: Protective Earth Terminal
This warranty does not apply to any machine Power Off that has been subjected to misuse, éteindre negligence or accident. Proluxe shall not be liable for the injury, loss or damage, direct or consequential, arising out of the use or the ... - Page 4 S A F E T Y S U M M A R Y and rating fuse. Listed Supplemental Fuse rated max 3A, 120Vac. Avertissement Pour une protection continue contre l’incendie Warning et de choc électrique, remplacer avec le même To reduce the risk of electrical shock, do not ...
- Page 5 This raise your machine off the table 4 inches. action forces the closing of the platens. Please contact sales at i nfo@proluxe.com for a set. Shipping charges may apply. (B) Thickness control dial. ...
-
Page 6: Controller Operation
Solid State Controller 4. R esetting the Counter: Press MODE button until the This controller has three (3) control features: counter is displayed. 1. T emperature – May be set from 100°-425°F (38°-163°C) To reset the counter (# of cycles), ... - Page 7 Note : Diameter and thickness is determined 1. Using a 3/16” hex shaped Allen through experimenting with your own dough wrench, insert in key slot located on and is a product of dough weight, temperature, the right beneath the upper shroud. pressing time, and thickness setting. ...
-
Page 8: Daily Care
This lubricant with a clean, soft cloth or soft sponge. can be ordered through Proluxe, part # 110-002. 2. E xterior surfaces: Wipe daily with mild ... - Page 9 Endurance X1M Troubleshoot Guide - Model #: DP1100M Problem Cause Action Ref # Power Button on 1. Power cord is not plugged in. 1. Plug the power cord into wall Digital Controller receptacle and power button. 68 ...
- Page 10 tactile button on may be not close enough to activate. time to avoid fracturing the digital controller, Same goes if the buttons are already traces on the controller) tighten nothing happens. pressed by overlay without the nuts on the back of the ...
- Page 11 10 ...
- Page 12 11 ...
- Page 13 Endurance X1M Part List - Model #: DP1100M ITEM DP1100MA DP1100MB DP1100MGB DP1100MCEB DP1100MCEC DESCRIPTION 120 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC 220 ~ AC QTY. BASE ASSEMBLY 110931101 110931101 110931101 110931101 110931101...
- Page 14 BRACKET, HOUSING ASSEMLBY 110144130 110144130 110144130 110144130 110144130 SCREW, SOCKET HEAD 1/4-20 X 3 1/4 SSH1420314 SSH1420314 SSH1420314 SSH1420314 SSH1420314 NUT, HEX 1/4-20 NH1420 NH1420 NH1420 NH1420 NH1420 BUSHING, TENSION STRAP 11018966 11018966 11018966 11018966 11018966 BUSHING, SPACER 11024369 11024369 11024369 11024369 11024369...
- Page 15 COVER PLATE, BASE 11010954 11010954 11010954 11010954 11010954 FEET, RUBBER RF209 RF209 RF209 RF209 RF209 BOLT, HEX 8-32 X 1/4 BH83214 BH83214 BH83214 BH83214 BH83214 POST, LOWER PLATEN 11015960 11015960 11015960 11015960 11015960 CABLE STRAIN RELIEF MPSS168 MPSS168 MPSS168 MPSS168 MPSS168 POWER CORD 110969174...
- Page 16 SCREW, BUTTON HEAD 1/4-20 X 3/4 SB142034 SB142034 SB142034 SB142034 SB142034 SCREW, BUTTON HEAD 1/4-20 X 5/8 SB142058 SB142058 SB142058 SB142058 SB142058 WASHER, SAE 3/8 WSAE38 WSAE38 WSAE38 WSAE38 WSAE38 PINION GEAR ASSEMBLY 1109360 1109360 1109360 1109360 1109360 ITEM DP1100MA DP1100MB ...
- Page 17 16 ...
-
Page 18: Warranty And Return Policy
1 year on parts and labor. This In no event shall Proluxe be liable for warranty applies to only equipment consequential damages arising out of the purchased and used in the United States. ... - Page 19 be returned after 30 days. If upon inspection 6. D amaged Claims : All merchandise shipped by Proluxe or its authorized agent it is at purchaser’s risk. Inspection must be made determined the equipment has not been used ...
Need help?
Do you have a question about the Endurance X1M and is the answer not in the manual?
Questions and answers