Advertisement
4. OPERATION
4.1.
Charging
4.1.1.
The air inlet (fig.1) is fitted with a 1/4"BSP female connection.
4.1.2.
Connect via an appropriate fitting to an air line.
4.1.3.
Open the air line and the air cock on the inlet fitting.
4.1.4.
Fill the air reservoir to air line pressure (150psi maximum) and close the inlet connector cock.
4.1.5.
Close the cock on the air line and disconnect.
4.2.
Using the seating tool in the horizontal position
4.2.1.
Adjust the barrel, so that the barrel flange is on the top (FIG.3).
4.2.2.
Ensure that both beads of the tyre have been well lubricated and position the wheel on a stand, the valve stem should be pointing
upwards and the wheel should be off the ground and the lower bead should be already seated.
4.2.3.
Attach an air line to the valve stem to simultaneously assist in the inflation process.
4.2.4.
Position the bead seater so that the weight of the unit is supported, rest the barrel flange on the rim of the wheel directly (fig.3)
opposite the valve stem. Attach an air line to the valve stem to simultaneously assist in the inflation process.
4.2.5.
Before use, the safety key should be removed from behind the trigger button (fig.2).
4.2.6.
The bead seater should be positioned at an angle of between 50 and 70 degrees, so that the barrel is pointing directly into the largest
gap between the tyre and the wheel.
4.2.7.
Holding the bead seater securely with one hand and keeping it steady against the wheel, press the trigger button to release the stored
air, and withdraw the nozzle from the bead/tyre interface.
4.2.8.
If the bead does not seat, recharge the tank to a higher pressure and repeat
NOTE:
Once the bead has been set; if required, move the wheel into a tyre cage and inflate to the manufacturer's recommended
pressure.
4.3
Using the Bead Seater in the upright position (truck tyres only).
4.3.1
Adjust the barrel, so that the barrel flange is on the bottom..
4.3.2
Position the wheel against a wall or a solid prop. Make sure that the valve stem is at the bottom and facing towards you.
4.3.3
Attach an air line to the valve stem to simultaneously assist in the inflation process.
4.3.4
The bead seater should be positioned at an angle of between 50 and 70 degrees, so that the barrel is pointing directly into the largest
gap between the tyre and the wheel.
4.3.5
Holding the bead seater securely with one hand and keeping it steady against the wheel, remove the safety key and press the trigger to
release the stored air.
4.3.6.
If the bead does not seat, recharge the tank to a higher pressure and repeat the procedure.
NOTE:
Once the bead has been set, if required, move the wheel into a tyre cage and inflate to the manufacturer's recommended
pressure. If the bead does not seat, recharge the tank to a higher pressure and repeat the procedure.
WARNING! Always wear the personal safety equipment as stated in section 1.1 whilst using this product.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
fig.3
01284 703534
sales@sealey.co.uk
Original Language Version
the procedure.
www.sealey.co.uk
TC904
Issue:1 - 16/01/18
Advertisement
