Subscribe to Our Youtube Channel
Related Manuals for Spraying Systems Co TankJet M60
Summary of Contents for Spraying Systems Co TankJet M60
- Page 1 TankJet M60 Mobile ® Tank Cleaner Operation & Maintenance Instructions Model: TJM60AG Tank Cleaner...
-
Page 2: Table Of Contents
TABLE OF CONTENTS FORWARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . -
Page 3: Forward
(1.4 bar). The maximum allowable pressure for the air motor is 20 psi (1.4 bar). The TankJet M60 comes with a set of valves mounted at the top of the cart handle. One valve is a high pressure 316SS valve needed to open and close the liquid line that supplies the nozzle head. The other valve is a trigger valve needed to open and close the air line that supplies air to the air motor needed to provide rotational motion to the nozzle head. -
Page 4: General Safety Instructions
• WARNING: Do not put any part of your body in the tank during operation of the tank cleaner. This is • WARNING: Spraying Systems Co. does not NOT a safe procedure for verification of operation. manufacture or supply any of the chemical components used in this equipment and is not •... -
Page 5: Assembly Instructions
There is some assembly and installation required before the TankJe M60 can be used for cleaning. Please see the information t® below for the tools needed to complete assembly of the TankJet M60 . Tools needed for assembly 1 . Adjustable Crescent Wrench 2. - Page 6 Step 3 . Step 4 . Mount handle to tube end with two holes to align with two Install two 1/4-20 flange head cap screws througn aligned holes on cart mounting post. holes in handle and cart mounting post. Insert handle and align two holes in handle with two holes on cart mounting post...
- Page 7 Step 7 . Install the included 1/4 NPT (male) x 1/4 NPS (swivel female) air hose. First, using an adjustable crescent wrench, connect the 1/4 NPT male end of hose to coupling marked air on handle assembly. Next, connect the 1/4 NPS (swivel female) end of hose to fitting on in side of air motor.
-
Page 8: Installation
. If a strainer valve. If your current systems does not have an air filter is needed Spraying Systems Co. can provide a strainer as pressure regulator, then this optional item can be provided an optional item . -
Page 9: Operation And Specifications
OPERATION AND SPECIFICATIONS Specifications Max. Operating Liquid Pressure 1,000 PSI (70 BAR) Max . Liquid Temp . 180°F (82°C) Motor Driven Type Air-Non Lubricated Max. Air Pressure 20 PSI (1.4 BAR) Max . and Min . Ambient Temp . +35°F to +125°F (+2°C to +52°C) Liquid Pipe Conn. - Page 10 Step 2 . Step 3 . Once, tank cleaner nozzle head is in tank, the tank WARNING! Never operate tank cleaner with cleaner can be used for tank washing operation. First, nozzle head outside of tank. Make sure ball valve turn the handle on the ball valve to the on position and is in off position for water line whenever nozzle head of then ajdust the water pressue regulator and temperature...
-
Page 11: Maintenance
It is suggested to change the seals after 300 hours of TankJet M60 operating time. Replacing Nozzle Hub Seals Replace worn seals in nozzle hub 1 . -
Page 12: Replace Gear Box Seals
Replacing Gear Box Seals Replace worn seals in gear box 1 . Adjustable Crescent Wrench 2 . Screw Driver Step 1 . Step 2 . First disconnect high pressure hose from round inlet Remove 4 #10-32 socket head screws from gear box body . - Page 13 Step 5 . Step 6 . Using a crescent wrench remove extension tube and First pull out drive tube and bevel gear from round inlet pinion gear. body . Then remove lower seal from round inlet body . Next disassemble round inlet cap by removing retainer ring with snap ring tool.
-
Page 14: Storage
STORAGE When the TJM60AG tank cleaner is not being used flush tank cleaner with clean water and then drain water from tank cleaner. Then store tank cleaner in a warm dry storage area. PARTS The following pages contains complete parts list drawing for the TJM60AG Tank Cleaner. The following table is a list the spare parts list for the TJM60AG Tank Cleaner. - Page 15 TJM60AG Tank Cleaner Handle Assembly with Water and Air Hose Assemblies (See Dwg. PL115240-3) TJM60AG Tank Cleaner Motor (Non-Lubricated) Assembly (see Dwg. PL115240-2) TJM60AG Tank Cleaner Wheel Assembly, Main Body & Drive Assemblies (See Dwg. PL115240-1) TJM60AG Tank Cleaner Spray Head and Gear Box Assemblies (See Dwg.
- Page 17 TJM60AG Tank Cleaner Motor (Non-Lubricated) Assembly ITEM DESCRIPTION PART N0. MATERIAL Air Motor Assembly (Non-Lubricated) 46340-TMJ60AG Hex Pipe Nipple 26396-1-SS Stainless Steel, Type 18-8 ...
- Page 19 TJM60AG Tank Cleaner Assembly with Water Hose Assembly ITEM DESCRIPTION PART N0. MATERIAL Spray Head Sub-Assembly 115255 Pinion Gear 72155-316SS Stainless Steel, Type 316 Fixed Tube 115246-316SS Stainless Steel, Type 316 Drive Tube 115252-316SS Stainless Steel, Type 316 115242-316SS Stainless Steel, Type 316 O-Ring 7717-2-121-BU BUNA-N (Nitrile Rubber)
-
Page 20: Data Sheets
TJM60AG Tank Cleaner ǀ 08/07/2017 • • •... - Page 21 ...
- Page 22 TJM60AG Tank Cleaner ǀ 08/07/2017 35 in [89.7 cm] 4 in [10.2 cm] 21 in [54.3 cm] 2 in [5.1 cm] 25.5 in [64.7 cm] 29.2 in [74.2 cm] 10.5 in [26.6 cm] 7.0 in [17.7 cm] ...
- Page 24 2.68 in [68 mm] 2.45 in [62.3 mm] 1.23 in [31.1 mm] 2 in [50 mm] 3.80 in [96 mm] 6.15 in [156 mm] Filter Regulator Relieving Type with 1/4 NPT Ports, 40 µm Filter, Manual Drain, Metal Bowl, Sight Glass and 0 to 30 P.S.I.
-
Page 25: Trouble Shooting Guide
TROUBLE SHOOTING GUIDE The following is a table indicating various potential modes of failure for this product. Mode of Failure Description Preventative or Corrective Actions Maximum pressure and Maximum fluid pressure for the TJM60AG Do not exceed maximum fluid temperature ratings is 1,000 PSI (70 BAR) pressure rating. -
Page 26: Warranty
If motor still does not run freely, motor may require major cleaning. Please refer to included Gast Air motor owner’s manual . SPRAYING SYSTEMS CO . WARRANTY ® Seller warrants that its products will conform to and perform in accordance with the products’ specifications. Seller warrants that the products do not infringe upon any copyright, patent or trademark. -
Page 27: Maintenance Records
MAINTENANCE RECORDS DATE PROCEDURE PERFORMED... - Page 28 P.O. Box 7900, Wheaton, IL 60187-7901 USA Tel: 1.800.95.SPRAY Intl. Tel: 1.630.665.5000 Fax: 1.888.95.SPRAY Intl. Fax: 1.630.260.0842 www.spray.com MI-TJ60 Tank Cleaner ǀ 08/07/2017 ǀ © 2017 Spraying Systems Co.
Need help?
Do you have a question about the TankJet M60 and is the answer not in the manual?
Questions and answers