HSS Hire 5000 Series Quick Start Manual

5000 Series Video Matrixes
The 5000 Series Video Matrixes provide video switching coordinated with lane selection in a 4000/5000 Series Audio
System. Images picked up by drive-in lane cameras are displayed on teller console monitors and the images from teller
console cameras are displayed on customer monitors while the teller is in two-way voice contact with a customer. During idle
times, console monitors display a choice of a wide-angle driveway camera or a rotation of available lane and driveway
cameras.
Lanes that are OFF or ON HOLD display Auxiliary video input, such as a videotape, video server, or solid-state video sign.
If no auxiliary video input is present, the customer's own camera image (viewback) is displayed.
Video Matrix Applications
Model Consoles Lanes
5005-4 3
5005-8 6
5005-12 6
5006 2

Installation

1. Complete the audio portion of the 5000 Series intercom installation as described in the audio matrix instructions;
calibrate the audio levels for all lanes and test all functions before starting the video installation.
In the following instructions, refer to the hookup diagram on the following page.
2. Remove power from the 5002 audio matrix. Mount the video matrix near the audio matrix. Connect the short RJ-45
cable supplied with the video matrix between the video matrix and the audio matrix (n/a for 5006 audio/video matrix).
3. Connect the console, camera and monitor for each teller position to the same numbered ports on the matrixes. For
example, console #1 is connected to CONSOLE 1 on the audio matrix, so connect its camera and monitor to the
CONSOLE 1 ports on the video matrix.
Connect cameras and monitors to the video matrixes using 75-ohm coaxial cable with solid copper center conductor and
BNC connectors. To minimize console monitor picture roll when switching, synchronize the lane cameras with each
other as instructed by the camera manufacturer. Generally, you must use the Line Lock Camera Mode and wire all
camera 24-volt AC inputs in-phase. Power all the cameras from the same 120-volt circuit if possible, and wire the 24-
volts the same on every lane camera. Test synchronization by switching from lane to lane at one of the console monitors;
the picture should not roll if the 24-volt wiring is correct. Slight vertical jumping can usually be adjusted out using the
Line Sync controls on the cameras. Note: DC powered cameras lack the line-sync feature, as do some 24 VAC cameras.
4. Connect a wide-angle driveway camera to the video matrix if you desire a wide shot of the drive-in area to be displayed
on idle console monitors. If a driveway camera is not connected, idle consoles will display a rotation of all available
individual lane cameras. If you have a driveway camera and want it to be displayed in rotation along with the lane
cameras, turn on Feature Switch 1 on the video matrix. Turn the switch off to display only the driveway camera.
5. Set the camera termination switch (labeled TERM) on the video matrix for each lane camera and the driveway camera to
the ON position if the video stops there. If the video is t-tapped on to some other device, such as a DVR, set the
termination switch OFF for that camera. In this case the termination must occur at the DVR. (Consult the DVR literature
for instructions). Failure to set the termination switches properly will affect both video quality and the ability of the
video matrix to lock in on a camera when that particular lane is selected by the teller.
6. If you want to display auxiliary video on unselected lanes, connect a VCR, DVR, video sign unit, or other video source
to the Auxiliary Video input on the Video Matrix. Set Video Feature Switch 2 ON if auxiliary video is static, that is, if it
does not move or change at least once every 5 seconds. Connect the audio output of the Auxiliary source, if so equipped,
to the Auxiliary Audio port on the 5002 Audio Matrix. Two jacks are provided for stereo sources; use either one for
monaural sources. Set Audio Feature Switch 5 (on the audio matrix), Noise Abate Mode, ON if you only want auxiliary
audio to be played after the call button is pressed or when the customer is on hold.
HFEA-OI5000VM (030206)
Use with Audio Matrix
4 5002-4
8 5002-8
12 5002-12
2 (audio built-in)
Feature Switch Settings
No. Function
1 Idle Console View
2 Aux Video
3 Not Used
4 Lane Shift
5 Not Used
UP (OFF) DOWN (ON)
Driveway Only All Cameras
Normal Static
Normal Shifted
Page 1 of 2