Subscribe to Our Youtube Channel
Summary of Contents for Sonodyne SMX Series
- Page 1 SMX SERIES SMX 1112/ SMX 1116/ SMX 1124 small format analogue mixers I owners manual www.sonodyne.com...
-
Page 2: Important Safety Instructions
If the unit is damaged, please notify your dealer and the shipping company immediately, otherwise claims for damage or replacement may not be granted. SMX SERIES page 1... -
Page 3: Initial Operation
XLR and TRS connectors. In addition, Trim Control allows line level input, to accommodate a wide variety of instruments BUILT-IN UNIVERSAL SWITCHING POWER SUPPLY The SMX Series features a universal switching power supply. This power supply supports input voltages of 100 V to 240 V, for stable operation even in environments where power voltage fluctuates easily. An AC inlet allows simple installation in environments where portability is required, as well as when mounting the mixing... -
Page 4: Connection Diagram
CONNECTION DIAGRAM AMPLIFIER LIVE INSTRUMENTS KEYBOARD MICROPHONES CD PLAYER ACTIVE SPEAKERS STAGE MONITOR HEADPHONE SMX SERIES page 3... - Page 5 CONNECTION DIAGRAM 18 19 SMX SERIES page 4...
- Page 6 For example, when routing to subgroups 3 and 4, panning hard left will route the signal to group output 3 only, and panning hard right will route to group output 4 only SMX SERIES page 5...
- Page 7 21. AUX SEND JACK: The AUX SEND jack carries the master aux mix(from the channel's AUX controls) 22. SUB OUT (1 - 2) JACKS: These impedance-balanced* TRS phone jacks output the SUB 1/2 signals. Use these jacks to connect to the input jacks of an multi-track recorder, external mixer, or other such device. SMX SERIES page 6...
- Page 8 35. FX SEND FADER: This is the master control for the Effects level. 36. MP3/BT FADER adjusts the level of MP3/BT. 37. SUB (1-4) FADER adjusts the signal level sent to the SUB OUT (1 to 4) jacks. 38. MAIN MIX FADER: This is the master level control for the MAIN OUTS. SMX SERIES page 7...
- Page 9 47. EQ IN SWITCH: Use this switch to activate the graphic equalizer. 48. BT: Press SWITCH for two seconds, the Signal LED will blink. Using mobile phone or tablet or pc, go to the BT device list and search for MIXER-01 to pair. Blinking stops when device is pared. Press the SWITCH again for 2 sec to disconnect BT. Restart BT to pair to another mobile phone or tablet PC. 49. SUB TO MAIN SWITCH: If this switch is on, the mixer sends the signals processed by the SUB faders onto the stereo bus. SMX SERIES page 8...
- Page 10 54. GND CONTACT: GND in order to avoid leakage. 55. CONTROL ROOM OUT JACKS: The control room output is normally connected to the monitoring system in the control room and carries the stereo mix or, when selected, the solo signals. SMX SERIES page 9...
-
Page 11: Cable Connections
For unbalanced use, PIN 1 & PIN 3 have to be bridged FOOT SWITCH CONNECTOR 1/4" TS FOOT SWITCH CONNECTOR Strain Relief Clamp Pole 2 Sleeve Sleeve Tip Pole 1/ground The foot switch connects both poles momentarily SMX SERIES page 10... -
Page 12: Audio Connections
(+ve) left signal (ground/ shield) (ground/ shield) Sleeve Sleeve Ring Ring Ring Ring cold (-ve) right signal For connection of balanced and unbalanced plugs, ring and sleeve have to be bridged at the stereo plug SMX SERIES page 11... -
Page 13: Troubleshooting
• Where an input channel provides both a XLR input jack and a phone input jack, or a phone input jack and an RCA pin jack, are there connections made at both jacks? Use only one of these jacks. • Are the [GAIN] knobs for each channel, channel faders, [STEREO] master fader, and [GROUP] fad- ers adjusted to appropriate levels? • Are effect or compressor levels too high? Use the [FX] knob, [FX RTN] fader, [FX RTN LEVEL] knob, and [COMP] knob to lower their levels. SMX SERIES page 12... - Page 14 • Are you using the same type of cable to connect both the left and right input signals? Cables with built-in resistors will attenuate the signal. The sound level is • Is the compressor level set too high? Use the TRIM knob to lower the unstable and inconsistent level SMX SERIES page 13...
-
Page 15: Specifications
MAX OUTPUT LEVEL +22dBu POWER REQUIREMENT 230V AC 50Hz POWER CONSUMPTION DIMENSION HxWxD (mm) 150 x 510 x 475 150 x 620 x 475 150 x 620 x 475 Due to continuous improvements, all specifications are subject to change SMX SERIES page 14... - Page 16 A product of the Mukherjee Innovation Centre Sonodyne Technologies Pvt. Ltd, 98 NB Block E New Alipore, Kolkata 700053, INDIA Tel: 1-800-123-37-36; E-mail: response@sonodyne.com Please visit us at www.sonodyne.com...
Need help?
Do you have a question about the SMX Series and is the answer not in the manual?
Questions and answers