ZIGBEE NR STH-03ZB User Manual

STH-03ZB User's Manual
Ver. 1.02
Copyright@2011 Nietzsche Enterprise Co., Ltd. All rights reserved.
Nietzsche Enterprise reserves the right to make changes and improvements to its products
without notice.
Contact information: E-Mail: service@nhr.com.tw; Website: www.nhr.com.tw
INDEX
1. STH-03ZB Manual ................................................................................................................ 2
2. What is in the box ................................................................................................................. 2
3. STH-03ZB Views .................................................................................................................. 2
4. Installing Mounting for STH-03ZB ......................................................................................... 3
5. Installing and Replacing Batteries in STH-03ZB ................................................................... 4
6. Setting Transmission Interval for STH-03ZB......................................................................... 5
7. Adding STH-03ZB to Receiving Device ................................................................................ 6
8. Removing STH-03ZB from Receiving Device ....................................................................... 7
9. STH-03ZB LED Signal Status ............................................................................................... 7
10. ZigBee Reset ........................................................................................................................ 8
11. Product Specifications........................................................................................................... 8
4. Installing Mounting for STH-03ZB
You will need:
Mounting fixtures
Drill with 5mm (approx. 0.2 inches) drill bit size (if using wall plugs) or 3.5mm (approx. 0.14
inches) drill bit size (if not using wall plugs)
Size 1 Phillips screwdriver
4.1 Locate STH-03ZB with at least 15cm (approx. 6 inches) spacing on each side (except
mounting side).
4.2 If it is necessary to pre-drill mounting holes, use mounting cradle to align locations for the 2
holes, then use appropriate drill bit to drill the holes - 5mm (approx. 0.2 inches) if using wall
plugs or 3.5mm (approx. 0.14 inches) if not using wall plugs. Note: pay careful attention to
orientation of the mounting cradle.
Orientation UP Arrow
4.3 If necessary, insert wall plugs into the 2 holes and use size 1 Phillips screwdriver for the 2
screws to secure the mounting cradle. Note: pay careful attention to orientation of the
mounting cradle.
4.4 Install and remove STH-03ZB using the following 2-step actions to ensure mounting has
been correctly and securely installed:
Install -
2
1
4.5 Initial hardware installation for STH-03ZB has been successfully completed.
STH-03ZB User's Manual
1
STH-03ZB User's Manual
Remove -
2
1
3
1. STH-03ZB Manual
Congratulations for choosing a world-class digital temperature and humidity sensor using
state-of-the-art ZigBee wireless transmission technology. This manual is designed to help set up
and get the most from the sensor in a few short minutes.
2. What is in the box
NHR STH-03ZB digital temperature Mounting fixtures (mounting cradle,
and humidity sensor 2 wall plugs, 2 screws)
If any of the above is missing, please contact your supplier.
3. STH-03ZB Views
The following is the front view of STH-03ZB
Status LED
Temperature & Humidity Sensor
The following is the side view of STH-03ZB
Product Serial Number &
Unique MAC Address
Link Switch
5. Installing and Replacing Batteries in STH-03ZB
You will need:
2 x AA batteries
5.1. Open the battery compartment using the following two-step action:
1
2
5.2. If necessary, remove existing batteries.
5.3. Install 2 AA batteries into the battery compartment.
5.4. The status LED on STH-03ZB should start flashing to indicate its current state:
Green LED Status
1 flash per second (loop) Ready to connect to coordinator or router device
1 flash every 60 seconds (loop) Already connected to coordinator or router device and
functioning normally
Rapid flashing (continue) Already connected but unable find coordinator or
router device
5.5. Replace battery compartment by first slotting base into STH-03ZB then clicking close the
compartment.
5.6. New batteries have been successfully installed.
Recommendation: It is strongly recommended to install batteries into STH-03ZB just before
adding to coordinator or router device as this will greatly improve battery life. For proper
functioning of STH-03ZB and longer battery life, please install alkaline batteries from reputable
suppliers.
Low battery power is indicated by the red LED repeating the following sequence: 2 rapid flashes
and pause 5 seconds. Replace batteries immediately to ensure correct functioning of
STH-03ZB.
STH-03ZB User's Manual
2 x AA batteries
The following is the base view of STH-03ZB
Transmission Interval Setting
The following is the back view of STH-03ZB
Battery Compartment
2
STH-03ZB User's Manual
1
2
4