Advertisement
3.7
BULk FILLING
3.7.1
Press the catch plate to release the plunger rod.
3.7.2
connect a low pressure bulk greasing unit to the bulk filler
nipple (fig.3B) at the top of the gun and fill until plunger rod
is fully extended.
3.7.3
Press and hold the catch plate and push the plunger rod
down until some resistance is felt. release catch plate.
3.8
OPERATION
3.8.1
Turn the trigger locking knob to the upper "unlock" position.
3.8.2
Slide the grease tube connector out of the stowage point on
the top of the unit (fig.3f) and push the connector onto the
chosen grease nipple and operate the trigger until the
desired amount of grease has been dispensed.
3.8.3
When the grease gun is not in use turn the trigger locking
button (fig 4.4) to the lower "lock" position .
3.9
ELIMINATING AIR POCkETS
3.9.1
if you encounter air pockets during operation the following
procedures can be used to eliminate them.
3.9.2
Hold down the catch plate and exert force on the plunger
(fig 4.K), whilst pressing the vent valve (fig 4.A).
3.9.3
operate the trigger (fig 4.H) in short, sharp bursts until
grease begins to flow from the connector at the end of the
flexible tube.
3.9.4
Slowly turn the thumb screw on top of the grease release
valve (fig.3c) anticlockwise until grease and air begin to
escape from the hole in the side of the valve. When all the
air has been expelled and only grease is escaping, shut the
valve by turning the thumb screw clockwise.
3.10
READING THE BATTERY DISPLAY
3.10.1 To check the remaining battery power, press and hold down
the LED display button (fig.3E) on the top of the grease gun.
A gauge will appear on the display (fig.3D) showing the
percentage of battery charge left. The display has five
segments, each representing 20% of the full charge.
4. TROUBLESHOOTING
CONDITION
Motor fails to run.
Pressure release valve opens to
discharge grease.
Grease gun fails to dispense
grease.
Grease gun continues to lose
prime.
Battery fails to charge.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
POSSIBLE CAUSE(S)
- Battery needs recharging.
- faulty wiring to motor.
- Blocked line.
- Blocked bearing.
- Blocked grease fitting.
- Grease tube is out of grease.
- Loss of prime.
- check valve is not functioning.
- Air may be trapped in locations
throughout the grease tube ass'y
after bulk filling.
- Grease tube follower may be
binding.
- charger may not have power.
- Battery may be dead.
Sole Uk Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
iP32 7Ar
Original Language Version
CORRECTIVE ACTION
- recharge battery.
- remove battery, disassemble
handle and check wiring for loose
connections.
- check lines, pipe joints and
grease fittings and remove any
obstructions.
- check that the tube contains
grease.
- repeat priming operation.
- remove check valve, clean and
inspect the valve seat.
- Empty grease tube ass'y, refill and
repeat priming operation.
- replace grease tube ass'y.
- check the mains charger is
providing power.
www.sealey.co.uk
01284 757500
Web
sales@sealey.co.uk
01284 703534
email
cPG18V
Fig.4
issue no.1 21/12/09
Advertisement
