Advertisement
Avoid unintentional starting and ensure the lock-on button is disengaged before use.
9
Use suitable detectors to determine if utility lines are hidden in the work area or contact local utility companies for assistance.
9
Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line
causes property damage and may cause electric shock.
Hold the tool only by the insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring
9
or its own cord. Contact with a "live" wire will also make the exposed metal parts of the power tool "live" and shock the operator.
When working with machine, always hold it firmly with both hands and provide for a secure stance. The power tool is guided more
9
securely with both hands.
Always wait until the machine has come to a complete stop before placing it down. The tool insert can jam and lead to loss of
9
control of the power tool.
Take protective measures when dust can develop during working that is harmful to one's health, combustible or explosive.
9
Always use the auxiliary handle supplied with the machine. Loss of control can cause personal injury.
9
DO NOT work materials containing asbestos. Asbestos is considered carcinogenic.
8
DO NOT force the drill to achieve a task it was not designed to perform.
8
DO NOT operate drill where there are flammable liquids or gasses.
8
DO NOT get the drill wet or use in damp or wet locations.
8
DO NOT operate the drill if any parts are missing or the drill is damaged as this may cause failure and/or possible personal injury.
8
DO NOT operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry the drill with your finger on the power switch, or carry by the power cord, or leave the drill running whilst unattended.
8
DO NOT over-reach and ensure the floor is not slippery and wear non skid shoes.
8
DO NOT hold unsecured work in your hand.
8
DO NOT use the machine with a damaged cable. DO NOT touch the damaged cable, but turn off the power supply at socket.
8
DO NOT use the drill without the auxiliary handle fitted
8
When not in use, switch drill off, remove plug from power supply, clean the drill and store in safe, dry, child proof area
9
1.3.
DIAMOND CORE DRILL BIT SAFETY
WARNING! Once a core cutter is within the hole and cutting, it can snag or grab at any moment without warning. This can easily
‰
harm your wrist or arm.
When drilling through floors make sure the area beneath the floor you are working on is cordoned off and that co-workers are aware
9
of what you are doing. The core is likely to fall from the ceiling when you have finished drilling.
Check both the inside and outside of the core drill for damage, wear or debris before using it.
9
Silica dust will be created when drilling concrete wear a mask.
9
Diamond core drilling is the slowest method of cutting a hole. Have realistic expectations as to the time required for cutting.
9
2. INTRODUCTION
Manufactured using high quality components for performance and reliability. Lightweight and compact unit. Fitted with soft start, variable
speed and overload protection. Designed for use in construction and other applications when working with masonry and concrete. Supplied
with adaptor, water cooling kit and side handles. Can be used independently or with optional Model No. DCDST Diamond Core Drill Stand.
3. SPECIFICATION
Model No:.............................................................. DCD110V
Masonry Drilling Range: ..................................... Ø18-160mm
Concrete Drilling Range: .................................... Ø18-130mm
Power Supply: .....................................................110V - 50Hz
Motor Power:...............................................................2300W
No Load Speed: ..................................................0 - 1900rpm
Borehole Depth: ......................................................... 380mm
Maximum Cutter Size: ....................................Ø160 x 380mm
Adaptor: ....................................................1-1/4"UNC Thread
Optional Drill Stand: ..................................Model No. DCDST
Cable Length:................................................................. 3.5m
4. OPERATION
fig.1
WARNING! Make sure there are no cables or pipes hidden in the wall. Never assume that work hasn't been done by someone else
‰
in the intended drilling area beforehand.
© Jack Sealey Limited
Noise power ............................................................<85dB(A)
Noise pressure .......................................................... 69dB(A)
Vibration ................................................................... <2.5m/s²
Uncertainty ................................................................. 1.5m/s²
Original Language Version
DCD110V Issue 3 (3) 27/07/2020
Advertisement
