ZIGBEE S37157 Quick Start Manual

Plug-in Type ZigBee Control Module for 4 Channels Output LED Drivers
Important: Read All Instructions Prior to Installation
Function introduction
ZiBee Control Module
Program key
16 pin male connector to
connect with LED driver
Features
• ZigBee control module based on ZigBee 3.0 protocol
• Works with plug-in control module 4 channels output LED drivers
• Enables to control ON/OFF, light intensity, RGB color and color changing effect of RGBW LED
• W channel can not controlled independently, but can be switch on/off and dimmed together with RGB channels
• Supports Touchlink commissioning
• Can directly pair to a compatible ZigBee remote via Touchlink without coordinator
• Supports find and bind mode to bind a ZigBee remote directly without coordinator
• Compatible with universal ZigBee gateway products
• Compatible with universal RGBW ZigBee remotes
• Waterproof grade: Ip20
Safety & Warnings
• DO NOT assembly the control module with power applied to the LED driver.
• DO NOT expose the module to moisture.
• DO NOT change the control module within 1 minute after powering off the driver to avoid burning-out.
Operation
1.Assemble the control module
control module
09.09ZG4CH.04735
NC
NC
NC
NC
1-
Prog.
4 channels LED output,
2-
common anode
3-
4-
NC
NC
NC
NC
2.LED Driver Wiring:
Once the control module is assembled to the LED driver, do wiring of LED driver according to the wiring
diagram.
3.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible
systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee
system.
4.Zigbee Network Pairing Via Coordinator (Hub or controller interface)
1) By factory default, the device does not belong to any ZigBee Network, and the connected LED light will be
under a slow rhythm breath status.
2) Before Pairing to current ZigBee Network, please remove the device from previous Network that it was
paired to if any. (from your ZigBee Controller or hub interface or by manual)
3) From your ZigBee Controller or hub interface, choose to add lighting device and enter Locating/Pairing mode
as instructed by the controller.
4) Network Pairing Begins Automatically: Connected LED light blinks 6 times as the device automatically scans
for a compatible network controller to pair with.
5) After the device is located and paired to the ZigBee network, the connected LED light will stop blinking and
stay solid on, then the device will appear in your controller's menu.
6) The lighting device is now paired to the ZigBee network and can be controlled by ZigBee controller or hub
interface.
5.Pair a compatible ZigBee remote to the device via Touchlink without Coordinator
1) The lighting device does not belong to any ZigBee network by factory default and the connected LED light
will be under a slow rhythm breath status..
2) Power off and power on the LED driver continuously for 3 times (or click the "Prog" key 3 times continuously),
the connected LED light flashes 6 times and stays solid on. Touchlink commissioning procedure of the device is
initiated and a network is formed.
3) The device is to be discovered and paired via Toucklink commissioning procedure.
4) Bring the remote within 10cm of the device.
5) Set the remote to start Touchlink commissioning procedure. (please refer to its user manual to learn how).
6) There shall be indication on the remote that the remote is paired to the device via Touchlink successfully.
Note: each device can be paired to only one remote, and pairing to a new remote will remove the
previous pairing.
6.Pair to a compatible ZigBee remote directly via Find and Bind Mode without Coordinator
1)Power off and power on the LED driver (initiator node) or click the "Prog" key to initiate find and bind mode,
enable it to find and bind target. 25 seconds timeout if there is no target, repeat the operation.
2)Set the remote (target node) into find and bind mode, and enable it to find and bind initiator. (Please refer to
its user manual to learn how)
3)There shall be indication on the remote that the remote bind the device successfully.
7.Binding Between the Device and ZigBee Remotes Via Coordinator (Hub or controller interface)
Once the device and compatible remotes are paired to the same network, from your ZigBee controller or hub
interface, choose to bind the device to a remote as instructed by the controller. Then the device can be
controlled by the remote.
Note: Each device can only bind with one group (any group) of a remote. Each device can bind with
multiple remotes simultaneously.