Subscribe to Our Youtube Channel
Summary of Contents for Inepro 132320
- Page 1 Konica Minolta Kit - Bizhub 132320 Installation Manual | Konica Minolta Kit - Bizhub 132320 Inepro Kit number: 132320 Konica Kit number: 9967000267 © 2019 Inepro B.V. All rights reserved...
-
Page 2: Table Of Contents
2 Attach the bracket to the copier ................................ 11 Set up the copier 1 Konica Minolta Bizhub 250 Series ................................ 16 Set up the PayCon 1 Behaviour ................................ 19 2 Network ................................ 20 3 General Settings ................................ 21 Notes http://www.inepro.com Version 2.2.20 Inepro B.V. -
Page 3: Introduction
Introduction Part... - Page 4 2. Prepare and construct the hardware. To read more go to page 3. Set up the copier, read more on page 4. Set up the PayCon, you will find more information on page Konica Minolta Kit - Bizhub 132320...
-
Page 5: Check Kit Content
Check Kit Content Part... - Page 6 In the "KM Mounting kit for Bizhub 250/350" you should find: · KM cableset keycounter I/F · PayCon copier mounting bracket · KM screwset Bizhub 250 / 350 · KM Mounting plate Bizhub 250 / 350 · This manual Konica Minolta Kit - Bizhub 132320...
- Page 7 KM Screwset Bizhub 250 / 350 KM Screw set Bizhub 250 / 350 In the "KM Screwset Bizhub 250 / 350" you should find: · Cable guiders · Cable Relief · M4 x 5mm Dome shaped, cross head screws · M3 x 16mm Dome shaped, cross head screws ·...
- Page 8 Check Kit Content KM Cableset keycounter I/F KM Cableset keycounter I/F In the "KM Cableset keycounter I/F" you should find: · Rip tie · Ferrite core · Connection cable Konica Minolta Kit - Bizhub 132320...
- Page 9 PayCon copier mounting bracket PayCon copier m ounting bracket In the "PayCon copier mounting bracket" you should find: · PayCon copier mounting bracket · Dome shaped, cross head screws · Dome shaped, cross head screws (not needed for this installation) Additional requirements for installation ·...
-
Page 10: Hardware Setup
Hardware Setup Part... - Page 11 Hardware Setup Additional requirements: · Pair of wire cutters · No. 2 cross head screwdriver · No. 1 PosiDriv head screwdriver · PayCon Copy · 2x CAT-5 Network cables (one cable included) Attach the PayCon to the PayCon bracket Please follow these steps: Break out the appropriate gaps in the flaps 2.
- Page 12 Close and gently screw dow n the final flap Place the PayCon bracket on the PayCon w ith the screw s from the bracket kit Konica Minolta Kit - Bizhub 132320...
-
Page 13: Attach The Paycon To The Bracket
Attach the PayCon to the bracket 6. Align the holes of the m ounting plate w ith the PayCon bracket and fasten it w ith the 3 M4 x 5m m screw s and their star lock w ashers Wrap the pow er w ire around the ferrite core twice, the netw ork cables once and attach the ferrite cores to the PayCon w ith the adhesive tape Place the connection w ire and its cable relief in the bracket Attach the PayCon bracket to the copier... - Page 14 5. Break out the hole in the cover. Place the cover and the bracket on the copier and guide the w ire through the hole in the cover and connect the w ire from the PayCon w ith that of the copier. Konica Minolta Kit - Bizhub 132320...
-
Page 15: Attach The Bracket To The Copier
Attach the bracket to the copier Screw the cover and bracket in place w ith the M3 x 16m m and M3 x 30m m screw s and fasten the cover w ith the cover screw 7. Place the 12 cable guiders Open the little side flap to feed the netw ork cable through Guide the cables through the 12 cable guiders... - Page 16 Hardware Setup 10. Rem ove the transport foils from the PayCon to finish the installation 11. Finished Konica Minolta Kit - Bizhub 132320...
-
Page 17: Set Up The Copier
Set up the copier Part... - Page 18 Select <OFF> (for correct working of duplex) Press <END> 8. Select <Total Counter> Select <Mode 2> (for correct working of duplex) Press <END> 9. Select <Large Size> Select <A3 11x17> Press <END> 10. Press <Reset> 11. Press <Exit> Konica Minolta Kit - Bizhub 132320...
-
Page 19: Konica Minolta Bizhub 250 Series
Konica Minolta Bizhub 250 Series... -
Page 20: Set Up The Paycon
Set up the PayCon Part... -
Page 21: Behaviour
Set up the PayCon Turn on the PayCon. Refer to the technical PayCon Copy manual for handling the PayCon menu and changing settings. The settings in the PayCon can be find in the tree-top menu structure of the PayCon. To simplify thing, we will use a graphic representation of this menu to show you where the setting can be found. - Page 22 Select 'Disabled', press and go to step 2f. , Go to 'Main Menu' => 'Card / ID' => 'Server Accounts' => 'Tags' => 'Inepro SLE'. e. Select 'Disabled' and press f. Do you use Pcounter? if you do, continue with step 3, if you don't, go to step 8.
-
Page 23: Network
Network 6. Fixed IP addresses: a. Set 'IP-address' to an IP-address in your network range and confirm with b. Set the subnet mask ('netmask') to '255.255.255.0' or to the subnet mask needed in your network and confirm with c. Set the 'default gateway' to the IP-address of the default gateway in your network and confirm with 7. - Page 24 12. Maximum Balance, the Maximum Balance allowed on a card or account. , Go to 'Main Menu' => 'Card/ID' => 'Generic Settings' => 'Maximum Balance'. b. Type in the maximum balance and confirm with Konica Minolta Kit - Bizhub 132320...
-
Page 25: General Settings
General Settings 13. Project ID, the unique number for all PayCon's on this project or site. , Go to 'Main Menu' => 'Terminal' => 'Project ID' b. Press , type the Project ID and confirm with 14. Date and Time, the time and date that are used for the timestamp on the transactions. Remember if the timezone is changed the time will change accordingly. -
Page 26: Notes
Notes Part... - Page 27 Notes This area is meant for the reader's notes:...
- Page 28 Notes Konica Minolta Kit - Bizhub 132320...
Need help?
Do you have a question about the 132320 and is the answer not in the manual?
Questions and answers