Download Print this page

Sealey PTB91508 Instructions page 2

Topchest 8 drawer 915mm heavy-duty/rollcab 6 drawer 930mm heavy-duty

Advertisement

4.3.
Install Wheels (Rollcabs) (Refer to fig.2).
4.3.1. carefully lay rollcab on its back, with a soft mat underneath for protection. Install the two braked casters on the same end as the handle.
4.3.2. Insert the carriage bolts through washers, then through the casters and into the bottom of the cabinet. tighten securely.
4.3.3. Install the fixed wheels on the opposite end to the handle.
4.4.
Remove Drawers (Refer to fig.3).
4.1.1. Pull drawer out until it is almost fully extended. Push up one black release lever, while pulling down the other hand black release lever.
4.1.2. Whilst holding the levers in these positions pull the drawer out until it is released from the drawer slide.
4.5.
Replace Drawers (Refer to fig.3).
4.5.1. Extend the drawer slides from the tool chest/cabinet.
4.5.2. Insert the brackets on each side of the drawer into the slots in the chest/cabinet slides, being careful that they are properly positioned.
4.5.3. once properly inserted, completely close the drawer to set the slides in their proper positions.
4.6.
Raise and Release Drawer Handles (Refer to fig.4)
4.6.1. these units are equipped with raise and release drawer handles.
4.6.2. To open, lift up the drawer handle, whilst pulling it towards you. To close, shut the drawer firmly, until the latch engages.
4.6.3. If the drawer does not stay closed, the hook may be bent or it may rub against the drawer slides. To fix lightly bend the hook until the
drawer will engage in the slide.
4.7.
Chest and Cabinet Connection (Refer to fig.5) (Option PTB91508 or PTB915TR)
4.7.1. take out the work top from on top of the cabinet.
4.7.2. Place the chest on the cabinet.
4.7.3. Attach the connectors and make sure the hook head snaps into the square hole on the back of the chest. fasten the screws to the
cabinet.
5. maINteNaNce
5.1.
Lubricate the casters annually with bearing grease.
5.2.
Lubricate the slides twice a year.
5.3.
Periodically the drawer fronts, drawer trim and other surfaces
should be cleaned with mild detergent and water.
Parts support is available for this product. To obtain a listing and/or diagram, please log on to: www.sealey.co.uk,
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
ImportaNt: no liability is accepted for incorrect use of this product.
warraNty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey Limited
Fig.3
Fig.5
email: sales@sealey.co.uk or phone: 01284 757500
Environmental Protection
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park,
Bury st. Edmunds, suffolk,
IP32 7Ar
Original Language Version
www.sealey.co.uk
01284 757500
01284 703534
sales@sealey.co.uk
PtB91508, PtB93006 | Issue: 3(L) - 06/01/17
Fig.4

Advertisement

loading

This manual is also suitable for:

Ptb93006