Wylie i3000 Quick Reference
  1. Manuals
  2. Brands
  3. Wylie Manuals
  4. Construction Equipment
  5. i3000
  6. Quick reference

Wylie i3000 Quick Reference

Telescopic crane
Hide thumbs
1
2
3
4
5
6

Advertisement

Table of Contents

55M3000AQE
i3000 TELESCOPIC CRANE INTERFACE DESCRIPTION
BOOM LENGTH
HOIST
STATE DISPLAY
ATB
active
Approach warning
of overload
SLEW ANGLE
PARTS (FALLS)
BOOM ANGLE
DISPLAY BUTTONS PRESENTATION
Shows system's modes.
Shows hoists for selection. Also
used to scroll up in menus or
increase modifiable values.
Shows parts of line (falls). Also
used to scroll down in menus or
decrease modifiable values.
Escape from a menu list. Also
used to cancel modification of a
value.
Select button. Used to select a
highlighted item in a menu.
Press button #1 and button #4 simultaneously to reset
+
the system. This could be usefull if the system stalls or
becomes unstable due to DC power supply regulation.
HEIGHT
RADIUS LOAD
UNITS
ALARMS
Rope
limitation
Overload
condition
Shows the problem source when
a fault is detected.
Shows the menu for the selection
of duty by number or by crane
configuration.
Shows
regarding
configuration.
Bypass the motion cut (lockout).
Enter the rigging mode.
Switch the load display between
the actual load and the tare
load.
DUTY NUMBER
BARGRAPH
LOAD CAPACITY
Preset limit(s)
reached
Cut-off
condition
all
the
information
the
actual
crane
Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the i3000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Wylie i3000

  • Page 1 55M3000AQE i3000 TELESCOPIC CRANE INTERFACE DESCRIPTION SLEW ANGLE PARTS (FALLS) HEIGHT DUTY NUMBER BOOM LENGTH HOIST BARGRAPH STATE DISPLAY LOAD CAPACITY RADIUS LOAD UNITS BOOM ANGLE ALARMS Rope Preset limit(s) active limitation reached Approach warning Overload Cut-off of overload condition...
  • Page 2 1- To enter rigging mode, the capacity of the crane must be at the floor value listed in the first column of the crane’s chart or under the boom rigging angle set in the i3000 calibration mode . 2- Push button #9.

  • Page 3: System Configuration

    55M3000AQE SYSTEM CONFIGURATION CONFIGURATION SETTINGS OF THE SYSTEM (CONFIG. SYSTEM): Numerous parameters can be configurated by the operator. These parameters are grouped in the menu config system and they include : language selection, units selection, reverse video, fails enable or disable. To modify one or more of these options you must access the config system menu as follows: 1- Push the MODE button (#1).

  • Page 4: Diagnostic Menu

    55M3000AQE SYSTEM CONFIGURATION AND DIAGNOSTIC MENU REVERSE VIDEO: You can invert the colors (black <--> white) to aid the operator’s vision of the display in various lighting conditions. 1- Push the MODE button (#1). 2- Scroll down with the down button (#3) to highlight the «config.system»...
  • Page 5 55M3000AQE i3000 RANGE LIMITING DEVICE (OPTIONAL) Shows which limit is reached: Shows which zone is programmed: limit high (roof) RADIUS variable limit height HEIGHT variable limit radius WALL free zone (two walls) APPROACH WARNING OF LIMIT CUT-OFF ALARMS: THE LIMIT...
  • Page 6 55M3000AQE i3000 RANGE LIMITING DEVICE (OPTIONAL) 3) VARIABLE LIMIT HEIGHT: 1- Access the range limiting mode. 2- Use the up and down buttons to highlight «variab.limit height». 3- Push button #4 to confirm your choice. 4- Rotate the crane to the first limit position (first wall).

Table of Contents