1. Manuals
  2. Brands
  3. U.S. Products Manuals
  4. Ultrasonic Jewelry Cleaner
  5. TORRENT-120
  6. Information & operating instructions

U.S. Products TORRENT-120 Information & Operating Instructions

Hard surface cleaner 120v
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HARD SURFACE CLEANER
CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ
ALL SECTIONS OF THIS INSTRUCTION MANUAL
IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY
1. DANGER: High pressure may cause sever injury. Always wear safety glasses.
NEVER direct the spray towards yourself, other people, or pets.
2. Never allow the spray to remain fi xed in one spot.
3. Before each use, remove the spray tool from the hose, and check to make sure the
spray nozzle is securely tightened in the tool. A loose nozzle could fl y off during use.
4. If a leak occurs at the hose, IMMEDIATELY turn the machine off. Replace the hose
before restarting.
5. Always use a defoamer to prevent vacuum motor damage when foaming occurs.
6. Keep the machine from rain in snow, extremes in temperatures, and store it in a
heated location. Use the machine indoors. Do not use outdoors.
7. NEVER adjust the pump above 1200 psi.
TORRENT
120V
INFORMATION
INSTRUCTIONS
®
&
OPERATING
revised 11/10 FORM NO. 56041838

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TORRENT-120 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for U.S. Products TORRENT-120

Summary of Contents for U.S. Products TORRENT-120

  • Page 1 ® TORRENT HARD SURFACE CLEANER 120V INFORMATION & OPERATING INSTRUCTIONS CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THIS INSTRUCTION MANUAL IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY 1. DANGER: High pressure may cause sever injury. Always wear safety glasses. NEVER direct the spray towards yourself, other people, or pets.

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops, and offi ces other than normal residential housekeeping purposes. When using any electrical appliance, basic precautions should always be followed, including the following: NOTE: Read all instructions before using this machine.

  • Page 3: Cleaning Solutions

    Record the serial number and model of your new extractor here: (and be sure to register your purchase to active your warranty -- go to www.usproducts.com) Serial Number: __________________ Model: TORRENT-120 Purchase Date:_____________ Write the name and phone number of your distributor:...

  • Page 4: Front Panel

    AND the switch is on the PRESSURE ON position. U.S. PRODUCTS High Pressure Pump Switch (4): Turns on/off the high pressure (400-1200 psi) pump. Dual Cord Sensor Light (5): The green light will turn on only when the two power cords are plugged into separate circuits.

  • Page 5: Recovery Tank

    RECOVERY TANK: (refer to Figure 2) Pre-Filter: 800 micron polyester mesh bag with quick-change cord lock. This fi lter hangs inside the tank from the recovery hose inlet piping. Check the pre-fi lter before operation and clean as required. Stainless Steel Filter: 50-mesh fi lter screws into base of recovery tank. Inspect daily and clean as needed. Float Valve: Located on the back wall in recovery tank, it automatically controls dump pump when switch is in ON position.

  • Page 6: Operation

    OPERATION 1. Before each use, inspect the machine, hoses, and cleaning tools for cleanliness and completeness. Make sure hoses are in good condition and the spray nozzle(s) is tight. 2. Connect direct water feed hose (supplied with chemical feed and back fl ow preventer) to the water supply and to the machine.
  • Page 7 AUTO-FILL: Without Chemical Injection: Simply connect one end of the water supply hose to a convenient water supply, and connect the other end to the water inlet fi tting on the machine. NOTE: hot water cleans better than cold water. When all set-up and ready to begin cleaning, turn on the water supply.

  • Page 8: Pump Maintenance

    PUMP MAINTENANCE: Oil Change: The fi rst oil change is required after the fi rst 50 hours of use. Impurities will get into the oil during the break-in phase, and it is necessary to change the oil to remove the contamination that can lead to premature pump wear.

  • Page 9: General Troubleshooting

    TORRENT PUMP MAINTENANCE SCHEDULE It is critical that you maintain your pump properly in order to get the performance and longevity that it can provide. Change the oil in your pump after the fi rst 50 hours of operation, then follow this maintenance schedule. AS NEED- TASK DAILY...
  • Page 10 TORRENT 120V 11-20-2010 10 - FORM NO. 56041838 - TORRENT...
  • Page 11 Item Ref. No. Description Item Ref. No. Description Clamp, cable 1490 Filter, In-line with swivel Hose clamp Hose barb 1349 Spacer 1489 Valve, thermal protection Washer, rubber Quick disconnect 1350 Bracket, fl oat 411A Fan, cooling Cord retainer Guard, fan 230A Nut, plastic 1501...
  • Page 12 ® TORRENT HARD SURFACE CLEANER 120V NOTES: 425-322-0133 / 800-257-7982 / FAX: 425-322-0136 11015 - 47th Ave. W. / Mukilteo, WA 98275 VISIT US AT: http://www.usproducts.com...

Table of Contents