Renkforce 1362482 Operating Instructions

G Operating instructions
Quad LNB
Item no. 1362482
Intended use
The product is designed to be installed on the LNB bracket (Ø 40 mm) of a satellite antenna and is
used to receive the appropriate digital satellite signals (TV, radio).
A satellite receiver can be directly connected to each of the four outlets of the Quad LNB. No
multi-switch or the like is necessary.
Always observe the safety instructions and all other information included in these operating in-
structions.
This product complies with the applicable national and European requirements. All names of com-
panies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• LNB
• Operating instructions
Explanation of symbols
This symbol points to specific risks associated with handling, function or operation.
The "arrow" sy mbol points to special tips and operating information.
Safety instructions
D amage due to not following these operating instructions will void the warranty! We
do not assume any liability for any resulting damage!
W e do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions. In such cases, the warranty will
be null and void.
• The unauthorised conversion and/or modification of the product is not permitted for
safety and approval reasons (CE). Do not disassemble the product.
• The product is not a toy and should be kept out of the reach of children.
• The product is designed for operation outdoors. Pay attention to the correct operat-
ing position during installation (ports must face downwards).
• Pay attention to the safety instructions and the information about the installation that
are mentioned with regard to your satellite antenna. The same applies to connecting
the cables/devices to the outlets of the LNB.
• During installation and connection, observe all of the necessary accident prevention
regulations for e.g., when you use a ladder to install the LNB to a satellite antenna.
Use only suitable tools for the installation and connection.
In case of doubt, leave the installation and connection work to a specialist!
• Do not leave packaging material carelessly lying around, since it could become a
dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows, or accidental
falls, even from a low height.
Assembly
Attention, important!
If you do not have the expertise to install the device correctly, please contact an expert
or a specialist workshop and let them carry it out!
A suitable measuring device is necessary for the optimal setting of a satellite antenna
with the LNB for digital TV/radio reception installed inside.
Install the LNB to the appropriate bracket (feed reception) of your satellite antenna. The bracket
must accordingly have an opening diameter of 40 mm.
The round side of the LNB must point towards the satellite antenna. Additionally, make sure that
the ports of the LNB lie downwards.
There is a degree indicator on the side of the LNB. The LNB is to be rotated depending
on your location and the satellite you would like to receive.
Connection
A satellite receiver can be directly connected to each of the four outlets of the Quad LNB. No
multi-switch or the like is necessary. Of course you can also use two random outlets to connect a
satellite receiver with twin tuner.
However, if there are more than four users to be connected to the Quad LNB, you need
a suitable multiswitch that is compatible to the Quad LNB.
If the multiswitch that you use only support a Quattro-LNB, you must change the multi-
switch.
Connect each outlet of the Quad LNB with the inlet of your satellite receiver via a suitable antenna
cable and corresponding F-plug.
It is absolutely necessary to use a high-quality, doubly shielded antenna cable suitable
for satellite signals so that the signals of the LNB are optimally routed.
If the cable between the LNB and the satellite receiver is very long, make sure that the
cable has a low damping.
The F-plug that is used to connect to the LNB must be suitable for operating outdoors
so that no moisture can penetrate.
In any case connect four cables to the Quad LNB and lay them in the interior even if you
want to connect less than four users to the LNB.
Slide the weatherproofing plastic cover of the LNB over the four F-plugs. It protects them addition-
ally from precipitation.
Disposal
The product must not be disposed of in the household waste.
Please dispose of the product at the end of its service life according to the current
statutory requirements.
Technical data
Power supply ...............................................via the satellite receiver or multiswitch
Operating voltage.........................................13 - 19 V/DC
Power consumption.....................................max. 190 mA
Frequency range (Inlet)...............................Low band: 10.7 - 11.7 GHz
.........................................................................High band: 11.7 - 12.75 GHz
Frequency range (Outlet) ............................Low band: 950 - 1950 MHz
.........................................................................High band: 1100 - 2150 MHz
L.O frequency................................................Low band: 9.75 GHz
.........................................................................High band: 10.6 GHz
Band control .................................................Low band: 0 kHz
.........................................................................High band: 22 kHz
Polarity switching ........................................V = 11.5 - 14 V/DC
.........................................................................H = 16 - 20 V/DC
Design ............................................................Quad-LNB
Outlets ............................................................4
Impedance ....................................................75 Ω
Amplification .................................................55 dB (typical)
Noise factor ..................................................0.4 dB (typical)
Feed receiver ................................................Ø 40 mm
Dimensions (L x W x H) ...............................120 x 68 x 81 mm
Weight ............................................................approx. 220 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.