Table of Contents
Advertisement
Quick Links
Assembly instructions
Installation, commissioning, utilization and maintenance
DE
ACHTUNG! WICHTIGE SICHERHEITSANWEISUNGEN!
Den Hinweisen auf Seite 2 dieses Handbuchs ist Folge zu leisten.
EN
ATTENTION! IMPORTANT SAFETY INFORMATION!
Follow the instructions on page 2 of this manual.
FR
ATTENTION! IMPORTANTES INDICATIONS DE SÉCURITÉ!
Les instructions de la page 2 de cette notice de montage doivent
être observées strictement.
ES
ATENCION INDICACIONES IMPORTANTES DE SEGURIDAD!
Deben seguirse las indicaciones detalladas en página 2 de estas
instrucciones de montaje.
IT
ATTENZIONE! INDICAZIONI SULLA SICUREZZA IMPORTANTI!
Prestare attenzione alle note alla pagina 2 delle presenti istruzioni
di montaggio.
NL
LET OP! BELANGRIJKE VEILIGHEIDSINSTRUCTIES!
Volg de instructies op pagina 2 van deze handleiding op.
DA
PAS PÅ! VIGTIGE SIKKERHEDSANVISNINGER
Oplysningerne på side
TST
LGB
Length Variants
-A / -B / -C / -D / -E
2
monteringsvejledning
denne
ATTENTION
IMPORTANT SAFETY
INFORMATION
For reasons of personal
safety, it is important to
follow these instructions.
Store these instructions.
skal følges.
Advertisement
Table of Contents
Summary of Contents for Feig Electronic TST LGB
- Page 1 Assembly instructions Installation, commissioning, utilization and maintenance Length Variants -A / -B / -C / -D / -E ACHTUNG! WICHTIGE SICHERHEITSANWEISUNGEN! ATTENTION Den Hinweisen auf Seite 2 dieses Handbuchs ist Folge zu leisten. ATTENTION! IMPORTANT SAFETY INFORMATION! IMPORTANT SAFETY Follow the instructions on page 2 of this manual. INFORMATION ATTENTION! IMPORTANTES INDICATIONS DE SÉCURITÉ! Les instructions de la page 2 de cette notice de montage doivent...
- Page 2 Puede encontrar estas instrucciones de montaje en el área de descarga en www.feig.de. Se ruega ini- ciar sesión con los siguientes datos de acceso: Nombre de usuario: Download / Password: feig FEIG ELECTRONIC GmbH Page 2 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx...
- Page 3 Assembly instructions Download feig FEIG ELECTRONIC GmbH Page 3 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx...
- Page 4 To the best of our knowledge, we believe that the accumulation of the information compiled in this document is valid. FEIG ELECTRONIC GmbH does not warrant the accuracy or completeness of the information in this document. FEIG ELECTRONIC GmbH will not be held liable for consequential damages arising as the result of incorrect or incomplete information.
- Page 5 These assembly instructions describe the following product variants and are only valid for these: TST LGB in the length variants -A / -B / -C / -D / -E The following characters are used in the functional description to point out the different danger zones and useful hints.
-
Page 6: Table Of Contents
Connecting the RLGxA wiring board to the controller ............17 Commissioning Setup assistant ........................... 19 Light beam adjustment ......................20 Functions Intelligent blanking ........................21 Manual blanking of light beams....................21 Safety outputs Status indicator Maintenance Technical Data Declaration of conformity FEIG ELECTRONIC GmbH Page 6 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx... -
Page 7: General Description And Intended Use
The interface of the door controller configures the parameters, diagnoses and tests the TST LGB. On basis of position data returned by a position detector mounted onto the door’s shaft, the TST LGB can determine the position of the door`s edge. -
Page 8: Safety Information
The manufacturer has carefully checked this document for accuracy; however, no guarantee is offered with regard to completeness and accuracy. Figure 2: Name plate At the end of the products life cycle, disposal is subject to statutory provisions. FEIG ELECTRONIC GmbH Page 8 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx... -
Page 9: Length Variants
Type Type Type Figure 3: Length variants ATTENTION The TST LGB variants must be selected in such a way that up to 2.50 m of the headroom of the door is supervised. FEIG ELECTRONIC GmbH Page 9 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx... -
Page 10: Installation
Light curtain bracket set (8 pieces) LGxASK Wiring board TST RLGxA-A Connection cable for transmitter TST KKAB-M12A4-15 Connecting cable for receiver TST KKAB-M12A8-5 4.1 Dimensions of the light curtain Mounting surface Figure 4: Outside dimensions FEIG ELECTRONIC GmbH Page 10 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx... -
Page 11: Safety Instructions For Installation
4.2 Safety instructions for installation ATTENTION To utilize the unit as exclusive safety device for the door (protection level E) the TST LGB must be installed at the center of the door frame. The lower end of the TST LGB must be installed at floor level. - Page 12 Assembly instructions Figure 5: Bracket positions for light curtains FEIG ELECTRONIC GmbH Page 12 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx...
- Page 13 Figure 6: Door frame top view 3. Mount the brackets to the door frame using the screws provided. 4. Press the light curtain into the brackets. Figure 7: Mounting the light curtain FEIG ELECTRONIC GmbH Page 13 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx...
-
Page 14: Electrical Connection
Pin 2 - white M12 /4 pole M12 /8 pole IMPORTANT! Female Female Connect these two wires M12 /8 pole M12 /4 pole Male Male Figure 8: Wire assignment for the light curtain FEIG ELECTRONIC GmbH Page 14 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx... -
Page 15: Wiring Diagrams For The Wiring Board Rlgxa
Assembly instructions 5.2 Wiring diagrams for the wiring board RLGxA Figure 9: Wiring diagram for the light curtain FEIG ELECTRONIC GmbH Page 15 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx... - Page 16 Assembly instructions Figure 10: Wiring diagram for position encoders FEIG ELECTRONIC GmbH Page 16 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx...
-
Page 17: Connecting The Rlgxa Wiring Board To The Controller
5.3 Connecting the RLGxA wiring board to the controller The TST RLGxA wiring board is a connection distributor which facilitates the connection of the TST LGB light curtain with the door controller. For this purpose, the red terminal block of the wiring board is plugged onto the red pin strip of the controller board (connection for the position encoder). - Page 18 3. Connect the light curtain and position encoder to the wiring board. (see chapter "Wiring diagrams for the wiring board RLGxA", page 15). 4. Plug the wiring board (c) onto the pin strip (a) (see point 4). FEIG ELECTRONIC GmbH Page 18 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx...
-
Page 19: Commissioning
6.1 Setup assistant The setup assistant checks the correct alignment of the TST LGB units to each. The Set-up assistant starts after reaching or storing the upper end position. From here, error messages of the light curtain may prevent further commissioning of the door. In the event of an error, these must be elimi- nated before continuing. -
Page 20: Light Beam Adjustment
Several light beams occupied. In the case of improvement of the Light beam alignment between the TST LGB units the signal quality rises. With good quality, the fault F 601 acknowledges itself automatically and the start up procedure may be con- tinued. -
Page 21: Functions
ATTENTION To be able to use the TST LGB as sole safety unit (protection level E) in accordance with EN 12453 on doors and gates with automatic operation and for use by non-trained personnel the mode "intelli- gent blanking"... -
Page 22: Safety Outputs
24 V Danger zone vacant 8,2 kΩ Danger zone vacant ATTENTION The 24V digital mode shall not be used as exclusive safety feature for the TST LGB application at the door. OUT2 Table 10: Safety output 2 OUT2 Output condition... - Page 23 An assignment in the danger zone leads to a hard stop, an assignment in the object zone leads to a, the door mechanics protective, slow braking of the door. FEIG ELECTRONIC GmbH Page 23 of 26...
-
Page 24: Status Indicator
Internal error, testing not successful 10 Maintenance The aperture for the entry and exit of the beams of the TST LGB transmitter and receiver must be cleaned once per door maintenance interval. Scratching by coarse agents or dissolving due to cleaning agents containing solvents must be avoided at all cost. -
Page 25: Technical Data
EN ISO 13849-1:2015 Cat 2/ PL d EN 12978:2003+A1:2009 IEC 61496-2:2006 EN 60335-1:2012-10 EN 61000-6-1:2007-10 EN 61000-6-2:2011-06 EN 61000-6-3:2012-11 EN 61000-6-4:2011-09 EN 60529:2014-09 IP 67 DIN EN 12453:2000 Protection level E DIN EN 12445:2000 FEIG ELECTRONIC GmbH Page 25 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx... -
Page 26: Declaration Of Conformity
Assembly instructions 12 Declaration of conformity FEIG ELECTRONIC GmbH Page 26 of 26 TST_LGB_Assembly_instructions_rev5_EN.docx...