Table of Contents
Advertisement
OPERATION
Adjusting the loud
- In loud mode, use
VOLUME
+
I
-
buttons (7&8) or VOL
4
/
b
buttons
(47) to switch between loud on and off.
When LOUD on, "LOUD" will show on
the display (4).
-
Directly press LOUD button (52) to
reinforce the bass output. Press it again
to release the function.
Adjusting the equalization
- In equalization mode, use
VOLUME
+
I
-
buttons (7&8) or VOL
4
/
b
buttons (47) to switch between the
following mode and the corresponding
information appears on the LCD (4).
r+
FLAT
--c
POP
--c
JAZZ -+ CLAS
1
L
2
- Directly press
EQ button (51) to turn
on equalization function and to select
desired audio mode as above.
Mute
Press MUTE button (3) on the front panel
or MUTE button (43) on remote control
to cut down sound output. Press it again
to resume the previous volume mode.
Setting the clock
Press DlSP button (44) to change the
display into clock display. While the current
time is appeared on the LCD (4), press it
again to return to frequency showing.
Holding down DlSP button (44) for several
seconds, and the time for hours is blinking
on the display (4), then press VOLUME
+
I
-
buttons (7&8) or V O L 4
/ b
buttons
(47) to switch between hours and minutes.
Press TUNE
+
I
-
buttons (1 3&14) or
TUNICH
A / V
buttons (46) to adjust the
hours or minutes.
Note: When you first press DlSP button
(44), the clock will appear on the LCD,
after several seconds, the clock will
disappear and the LCD enter into
frequency showing if you don't operate
it. Then you press DlSP button again, the
LCD remains the previous state and the
clock will not appear. You should press
DlSP button once again to display the
clock.
Radio Operation
Switching to radio mode
Press MODE button (1 2) on the front
panel or MODE button (42) on the
remote control to select radio mode,
the radio mode appears in the display
together with the memory band and
frequency.
Selecting the frequency band
Press BND button (1 1) on the front
panel or BAND button (40) on remote
control to select desired band. The
reception band will change in the
following order:
T
FM1+
FM2
+
FM3
+
AM1
+
AM2
1
Selecting station
During radio mode, press TUNE
+
button (1 3) or TUNICH
A
button on
remote control to increase frequency
or TUNE
-
button (1 4) or TUNICH
V
button on remote control to decrease
frequency by one step of channel
spacing. Hold the button longer for fast
tuning. The frequency is updated
corres~ondincllv on dis~lav.
-
<
,
,
Setting memory
Press preset memory buttons (1 -6)(15)
on the front panel or Radio Preset
buttons (1 -6) (37) on remote control to
preset stations at radio mode. With this
system, a total of 30 stations can be
stored in the memory of six buttons.
Each band stores up to six preset stations.
The stations might be FMI, FM2, FM3,
AM1 and AM2 band. The operation is
as below:
-
Store in Memory
Press and hold desired memory
location button for several seconds.
The current listening station will be
stored into the number button.
- Retrieve a Preset Station
Press any one of the buttons (1 5)
on the front panel or (37) on remote
control to retrieve a station which
had been stored in the memory in
advance the chosen number is
shown on display.
12
OPERATION
Automatically memory storing &
program scanning
-
Automatic memory storing
Press ASIPS button (48) for several
seconds, the radio searches from
the current frequency and checks
the signal strength until one cycle
search is finished. And then 6
strongest stations are stored into the
corresponding preset number button.
- Program scanning
Press ASIPS button (48) shortly to
scan preset station. When the field
strength level is more than the
threshold level of stop level. The
radio is holding at that preset
number for several seconds with
release mute, then searches again.
LocalIDistance
Press LOC button (38) on remote
control to select between local and
distant stations.
Local setting for reception of strong station,
and a distant setting for reception of weaker
stations. This function is effect during AUTO
SEEK
operation.
MonoIStereo
Press MOIST button (1 6) on the front
panel or STIMO button (53) on remote
control to select mono or stereo mode.
You can sometimes improve reception
of distant stations by selecting mono
operation.
Scan
Press -I-- (SCAN) button (39) on
remote control to set the function to
scan mode, which scanning to higher
frequency station with receivable signal
and keep on each station for several
seconds. At this time, press any one
of the buttons (1 5) on the front panel
or (37) on remote control, the current
scanned station will be stored into the
corresponding number button, then it
keeps on scanning other stations.
-
CDC operation
Switching to CDC mode
Press MODE button (12) on the front
panel or MODE button (42) on the
remote control to select CDC mode.
Selecting track
Press TUNWRACK
-
button (1 4) on the
front panel to move to the previous track;
press TUNIEITRACK
+
button (1 3) on
the front panel to move to the next track.
The track number shows on the display (4)
Pausing playing
Press PAU button (28) on the front
panel to pause CD play. Press it again
to resume play.
Previewing all tracks
Press INT button (29) on the front panel
to play the first 10 seconds of each
track on the current disc. Press it again
to stop intro and listen to track.
Repeating the same track
Press RPT button (30) on the front
panel to continuously repeat the same
track on the current disc. Press it again
to stop repeating.
Playing all tracks in random
Press RDM button (31) on the front
panel to play all tracks on the current
CD in random order. Press it again to
cancel the mode. In the course of
playing a track, press TUNE +I- buttons
(1 3&14) to play another track in random
order.
Selecting disc
Press CD+ button (33) on the front
panel to select next disc and press
CD- button (32) on the front panel to
select previous disc.
Advertisement
Table of Contents
