Nokia NPM-10 Series Disassembly/Assembly
  1. Manuals
  2. Brands
  3. Nokia Manuals
  4. Transceiver
  5. NPM-10 Series
  6. Disassembly/assembly
Nokia NPM-10 Series Disassembly/Assembly

Nokia NPM-10 Series Disassembly/Assembly

Hide thumbs Also See for NPM-10 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
CCS Technical Documentation
NPM-10 Series Transceivers
Disassembly/Assembly
Nokia Corporation
Issue 1 03/2003
Confidential

Advertisement

Table of Contents
loading

Related Manuals for Nokia NPM-10 Series

Summary of Contents for Nokia NPM-10 Series

  • Page 1 CCS Technical Documentation NPM-10 Series Transceivers Disassembly/Assembly Nokia Corporation Issue 1 03/2003 Confidential...
  • Page 2 NPM-10 Disassembly/Assembly CCS Technical Documentation Nokia Corporation Page 2 Confidential Issue 1 03/2003...

  • Page 3: Table Of Contents

    6. Remove Lightguide Assembly ................8 6.1 Remove Metal frame and Earpiece ..............9 7. Remove the PWB Assembly .................10 7.1 Remove shielding lids ..................10 8. Remove components from D-cover Assembly ............11 Nokia Corporation Issue 1 03/2003 Confidential Page 3...
  • Page 4 NPM-10 Disassembly/Assembly CCS Technical Documentation Nokia Corporation Page 4 Confidential Issue 1 03/2003...

  • Page 5: Disassemble The Npm-10 Transceiver

    The photo above shows a wrist strap, which can be grounded to a bench. This or some other form of ESD protection should be used when handling the phone. Assembly Use the Disassembly Instructions, which follow, in the reverse order. Nokia Corporation Issue 1 03/2003 Confidential Page 5...

  • Page 6: Remove B-Cover

    Lift the battery out by lifting from the bottom of the battery compartment. Remove SIM card 1 Press plastic spring down. 2 Place the thumb from the other hand on SIM card. Press and slide the SIM card towards the top of the phone. Nokia Corporation Page 6 Confidential Issue 1 03/2003...

  • Page 7: Remove A-Cover

    NPM-10 CCS Technical Documentation Disassembly/Assembly Remove A-cover Place thumb under the edge of the A-cover and fingers on top. Pull the A-cover gently until a snaps deactivates. Nokia Corporation Issue 1 03/2003 Confidential Page 7...

  • Page 8: Remove Screws (Torx #6)

    CCS Technical Documentation Remove screws (Torx #6) Remove Lightguide Assembly Use screwdriver size 2.50 – 3.50 mm Bottom connector Between PWB & Bottom connector. Be careful not to damage the Bottom connector. Nokia Corporation Page 8 Confidential Issue 1 03/2003...

  • Page 9: Remove Metal Frame And Earpiece

    1 Turn screwdriver at snaps, only on one side (#1a and 1b above). 2 When removing the metal frame, be careful not to damage the four springs in the corners (#2 above). 3 Remove the Earpiece (#3 above). Nokia Corporation Issue 1 03/2003 Confidential Page 9...

  • Page 10: Remove The Pwb Assembly

    CCS Technical Documentation Remove the PWB Assembly Remove PWB assembly. Place PWB on ESD table with LED upwards. Remove shielding lids Remove shielding lids, as shown above. Do not re-use shielding lids once removed. Nokia Corporation Page 10 Confidential Issue 1 03/2003...

  • Page 11: Remove Components From D-Cover Assembly

    When working with PWB, always use repair jig (shown below). Remove components from D-cover Assembly The following components are removable: 1 Power key 2 Battery connector 3 Vibra assembly 4 Bottom connector Nokia Corporation Issue 1 03/2003 Confidential Page 11...
  • Page 12 NPM-10 Disassembly/Assembly CCS Technical Documentation 5 MALT speaker Use screwdriver size 2.50 – 3.50 mm. Remove MALT speaker by turning the screwdriver as shown here. Nokia Corporation Page 12 Confidential Issue 1 03/2003...

Table of Contents