INTRODUCTION Thank you for purchasing a Patriot Equipment Gravity Tender! We know you will get many years of productive use from it. The product has been designed to perform a certain function. The Gravity Tenders can be stationary or can be pulled to a location depending which model has been purchased.
WARNING: A specific hazard or unsafe practice which could result in severe personal injury or death if proper precautions are not taken. CAUTION: Unsafe practices which could result in personal injury if proper precautions are not taken or a reminder of good safety practices. Gravity Tender V1.0...
Page 5
Do not allow anyone on the machine when in use or while in storage. Do not allow anyone to enter the hopper. In case of any defect or awareness of potential danger, please contact Patriot Equipment at 1-308-832-0220 immediately. Gravity Tender V1.0...
Page 6
Any person who has not read and understood all operation and safety instructions is not qualified to operate the machine. An untrained operator exposes himself and bystanders to possible serious injury or death. Do not modify the equipment in any way. Unauthorized modifications may impair the functions and/or safety and could affect the life of the equipment. Gravity Tender V1.0...
Page 7
I have the safety lock up pins and know and understand where and when to use them. I understand that any accidents that occur with the machine are my responsibilities. 10. I understand that Patriot Equipment will not be held responsible for any accidents that involve the machine. Sign Off Sheet...
Align the decal over the specified area and carefully press the small portion with the exposed sticky backing in place. Slowly peal back the remaining paper and carefully smooth the remaining portion of the decal in place. Small air pockets can be pierced with a pin and smoothed out using a piece of decal backing paper. Gravity Tender V1.0...
Page 9
Slide Style Coupler Bumper Pull Decal can vary with coupler style used Tire Information Generated at Factory VIN GVWR Generated at Factory TS2000 5x20 Red Patriot Decal TS2012 Single Pinch Point TS2017 Read Manual Before Use DOT White L Required marking...
Page 10
This drawing, and the information hereon, are the Patriot Equipment property of Minden Machine Shop Inc., and may be 1302 K Road Minden, NE used only as authorized by us. Unpublished - All rights 308-832-0220 reserved under the copyright laws. Gravity Tender V1.0...
Page 11
This drawing, and the information hereon, are the Patriot Equipment property of Minden Machine Shop Inc., and may be 1302 K Road Minden, NE used only as authorized by us. Unpublished - All rights 308-832-0220 reserved under the copyright laws. Gravity Tender V1.0...
Page 13
100 gallons, this tank when filled would weigh about 800 pounds. If more cargo is being transported, water can be off-loaded to keep the total amount of cargo added to the vehicle within the Gravity Tender V1.0...
Page 14
Locate the GVWR (Gross Vehicle Weight Rating) of the trailer on your trailer’s VIN (Certification) label. Subtract the empty weight of your trailer from the GVWR stated on the VIN label. That weight Gravity Tender V1.0...
Page 15
If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult the tow vehicle’s manual to determine how this weight transfer reduces the available cargo and luggage capacity of your vehicle. Gravity Tender V1.0...
Page 16
The maximum weight that any axle can support, as published on the Certification / VIN label on the front left side of the trailer. Actual weight determined by weighing each axle on a public scale, with the trailer attached to the towing vehicle. Gravity Tender V1.0...
Page 17
Non-pneumatic tire assembly A non-pneumatic tire, alone or in combination with a wheel or wheel center member, which can be mounted on a vehicle. Gravity Tender V1.0...
Page 18
Rim diameter This means the nominal diameter of the bead seat. Rim size designation This means the rim diameter and width. Rim type designation This means the industry of manufacturer’s designation for a rim by style or code. Gravity Tender V1.0...
Page 19
Wheel-holding fixture The fixture used to hold the wheel and tire assembly securely during testing. Gravity Tender V1.0...
Page 20
Vehicle capacity weight (VCW–the maximum occupant and cargo weight a vehicle is designed to carry) Front and rear gross axle weight ratings (GAWR– the maximum weight the axle systems are designed to carry). Both placards and certification labels are permanently attached to the trailer near the left front. Gravity Tender V1.0...
Page 22
Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a tire identification number for safety standard certification and in case of a recall. Gravity Tender V1.0...
Page 23
The "M+S" or "M/S" indicates that the tire has some mud and snow capability. Most radial tires have these markings; hence, they have some mud and snow capability. Gravity Tender V1.0...
Page 24
This letter indicates a tire's ability to stop on wet pavement. A higher graded tire should allow you to stop your car on wet roads in a shorter distance than a tire with a lower grade. Traction is graded from highest to lowest as "AA","A", "B", and "C". Gravity Tender V1.0...
Page 25
Max. Load Single kg (lbs.) at kPa (psi) Cold This information indicates the maximum load and tire pressure when the tire is used as a single. Load Range This information identifies the tire's load-carrying capabilities and its inflation limits. Gravity Tender V1.0...
Page 26
Make sure your tire valves have valve caps. Check tire pressure before going on a long trip. Do not overload your vehicle. Check the Tire Information and Loading Placard or User’s manual for the maximum recommended load for the vehicle. Gravity Tender V1.0...
Wheel Attachment and Torque Requirements Patriot Equipment would like to reiterate the extreme importance of properly matching your axles, wheels, and tires when specifying or replacing your trailer wheels. It is of equal importance that you apply and maintain proper wheel mounting torque on your trailer axle.
Page 28
There will be varying amounts of thread stick out depending on variables such as center disc thickness and nut thickness. In general, there should be approximately three threads visible past the end of the nut. Gravity Tender V1.0...
Page 32
This drawing, and the information hereon, are the Patriot Equipment property of Minden Machine Shop Inc., and may be 1302 K Road Minden, NE used only as authorized by us. Unpublished - All rights 308-832-0220 reserved under the copyright laws. Gravity Tender V1.0...
Page 33
This drawing, and the information hereon, are the Patriot Equipment property of Minden Machine Shop Inc., and may be 1302 K Road Minden, NE used only as authorized by us. Unpublished - All rights 308-832-0220 reserved under the copyright laws. Gravity Tender V1.0...
Page 34
This drawing, and the information hereon, are the Patriot Equipment property of Minden Machine Shop Inc., and may be 1302 K Road Minden, NE used only as authorized by us. Unpublished - All rights 308-832-0220 reserved under the copyright laws. Gravity Tender V1.0...
Page 35
This drawing, and the information hereon, are the Patriot Equipment property of Minden Machine Shop Inc., and may be 1302 K Road Minden, NE used only as authorized by us. Unpublished - All rights 308-832-0220 reserved under the copyright laws. Gravity Tender V1.0...
(N.m) manual. When using manual. When using locking elements, increase locking elements, increase torque values by 5%. torque values by 5%. 1206 Grade or Class value for bolts and capscrews are identified by their head markings. Gravity Tender V1.0...
The Patriot Gravity Tender allows for easy storage and/or transport of bulk feed to a farm location or to a field. The Patriot Gravity Tender has a rear or side discharge to make it easy for the operator to get bulk feed into a bucket or directly into a feed bunk.
Page 39
If equipped with a battery, disconnect the battery Clean the Gravity Tender and perform touch up painting to prevent rust or any corrosion Inspect and repack the wheel bearings so that the Gravity Tender is ready to go for the next season. Gravity Tender V1.0...
Page 41
This drawing, and the information hereon, are the Patriot Equipment property of Minden Machine Shop Inc., and may be 1302 K Road Minden, NE used only as authorized by us. Unpublished - All rights 308-832-0220 reserved under the copyright laws. Gravity Tender V1.0...
Page 42
(where wires attach) Ground Black Wire 5/16" Eyelets used here Ground Blue Break Away Blue Two Pin Weather Pack Connector White Break Blue Away Battery Black Minden Machine Shop Inc. 1302 K Road Minden, NE 800-264-6587 / 308-832-0220 Gravity Tender V1.0...
Page 43
This drawing, and the information hereon, are the Patriot Equipment property of Minden Machine Shop Inc., and may be 1302 K Road Minden, NE used only as authorized by us. Unpublished - All rights 308-832-0220 reserved under the copyright laws. Gravity Tender V1.0...
Page 45
This drawing, and the information hereon, are the Patriot Equipment property of Minden Machine Shop Inc., and may be 1302 K Road Minden, NE used only as authorized by us. Unpublished - All rights 308-832-0220 reserved under the copyright laws. Gravity Tender V1.0...
Page 46
This drawing, and the information hereon, are the Patriot Equipment property of Minden Machine Shop Inc., and may be 1302 K Road Minden, NE used only as authorized by us. Unpublished - All rights 308-832-0220 reserved under the copyright laws. Gravity Tender V1.0...
20 to 25 times at a low speed (under 25 miles per hour) to begin the “seating in” of the brake to the brake drum components. Do this in a safe and low traffic area for everyone’s safety. Gravity Tender V1.0...
Page 48
Now move the star wheel in the opposite direction until you can feel a little resistance from the brake and replace the hole cover. Carefully lower the tire to the ground. Repeat this procedure for all wheels making sure to adjust all brakes at the same time. Gravity Tender V1.0...
Page 49
Check brake system wiring. • Check for worn, damaged brake linings. • Check for weak or broken brake shoe return spring. • Check for worn brake drums. • Check that correct controller is installed. • Check for improper controller installation. Gravity Tender V1.0...
Page 50
Please note that the majority of electrical brake complaints can be traced to the controller. Refer to your brake controller manual to insure your controller is correctly adjusted and that the connections are in compliance with the manufacturer’s specifications. Gravity Tender V1.0...
Page 51
Hand pack each bearing individually using a premium lithium base wheel bearing grease. Reinstall the hub, reversing the procedure above using the bearing adjustment procedures below. If you have the Posi–Lube system, refer to the “Posi-Lube Lubrication Procedure”. Gravity Tender V1.0...
Page 52
Pump the grease into the fitting as you continue pressure you will notice the old grease coming out at the cap. When you begin to see the new grease, remove the gun and clean off any excess and replace the rubber cap. Gravity Tender V1.0...
Page 53
45-70 ft. lbs. ½” 45-70 ft. lbs. 9/16” 60-85 ft. lbs. Shackle Bolt Torque 7/16” 45-70 ft. lbs. 9/16” Not torqued, snug fit to allow parts to move easily. The lock nut is used to position parts. Gravity Tender V1.0...
Page 54
If needed remove the spring bushings and replace with new ones. Use the reverse order to reinstall your components. Special note: The fittings that attach the springs to the chassis mounts are designed specially to be wear resistant and should not be lubricated. Gravity Tender V1.0...
Page 55
Wheel Attachment and Torque Requirements Patriot Equipment would like to reiterate the extreme importance of properly matching your axles, wheels, and tires when specifying or replacing your trailer wheels. It is of equal importance that you apply and maintain proper wheel mounting torque on your trailer axle.
Page 56
There will be varying amounts of thread stick out depending on variables such as center disc thickness and nut thickness. In general, there should be approximately three threads visible past the end of the nut. Gravity Tender V1.0...
Page 57
Seal Replacement Brake Size Seal 7 x 1-1/4 4 or 5 Bolt 12192TB 10 x 2-1/4 5 or 6 Bolt 171255TB 12 x 2 6 or 8 Bolt 22333TBN 12 x 3-1/2 8 Bolt 22333TBN Grease 370219A Oil Gravity Tender V1.0...
Page 58
1/2 Stud & Nut TR1073 TR1085-1 9/16" Stud 6K Axle TR1074 TR1071 12 x 2" Brake Pad 1/2-20 Lug Nut TR1075 Minden Machine Shop Inc. 1302 K Road Minden, NE 9/16-18 Lug Nut TR1076 800-264-6587 / 308-832-0220 Gravity Tender V1.0...
Additional information on Proposition 65 can be obtained by visiting the State of California’s Proposition 65 website: https://oehha.ca.gov/proposition-65/about-proposition-65 Summary of Proposition 65 requirements: https://oehha.ca.gov/proposition-65/general-info/proposition-65-plain-language Clear and reasonable notice requirements: https://oehha.ca.gov/proposition-65/crnr/notice-adoption-article-6-clear-and-reasonable-warnings Chemicals and substances regulated by Proposition 65: https://oehha.ca.gov/proposition-65/proposition-65-list Proposition 65 Laws and Regulations: https://oehha.ca.gov/proposition-65/law/proposition-65-law-and-regulations Gravity Tender V1.0...
Page 60
Minden Machine Shop, Inc. has placed this decal on our products to alert the user to the possible exposures. Gravity Tender V1.0...
It is the policy of Minden Machine Shop Inc. to improve its products whenever possible and practical to do so. We reserve the right to make changes, improvements and modifications at any time without incurring the obligation to make such changes, improvements and modifications on any equipment sold previously. Gravity Tender V1.0...
City: State: Zip Code: Phone #: Email: Equipment: Serial #: Date Of Purchase: Equipment: Trailer Model Number: Trailer VIN Number: Date Of Purchase: Dealer Name: TIRE IDENTIFICATION NUMBERS QTY 1 Please return within 14 days of purchase Gravity Tender V1.0...