Advertisement
Quick Links
Advertisement
Summary of Contents for Energenie POM PDU
- Page 1 POM PDU per outlet monitoring & control User Manual...
-
Page 2: Table Of Contents
Table of Contents 1. Introduction ......................1 2. PDU Package ......................2 3. Function........................3 4. Installation ......................5 5. Web Interface ......................7... -
Page 3: Introduction
Indicate outlets and circuits status with LED. Support power on sequence. Schedule control User-defined group outlet control Auto reboot the locked device by pinging its IP Support network time protocols Option accessory can support temperature and humidity detection. POM PDU User Manual Ver. 1.0... -
Page 4: Pdu Package
The standard PDU package contains a Power Distribution Unit with supporting hardware and software. The components of the package are: Power Distribution Unit. Rack mount Brackets. CD-ROM, it contains: User Manual. PDU Software. MIB: Management Information Base for Network. (PDUMIB.mib) Adobe Acrobat Reader. POM PDU User Manual Ver. 1.0... -
Page 5: Function
SSL (yellow): Light on means that web access is protected by SSL. DHCP (green): Light on means that PDU gets IP address through DHCP. PDU (green): Indicate each output power status. Status (red): Indicate each circuit status. POM PDU User Manual Ver. 1.0... - Page 6 RJ11 for option ENV probe attached to detect temperature and humidity. Circuit Breaker Overload power protection. POM PDU User Manual Ver. 1.0...
-
Page 7: Installation
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips)." Diagram POM PDU User Manual Ver. 1.0... - Page 8 TO SETUP THE NETWORK SYSTEM FOR PDU, STRONGLY RECOMMAND TO BUILD UP THE POWER MONITORING NETWORK SYSTEM ISOLATED WITH THE OTHERS, IN ORDER TO KEEP THE STABILITY OF GETTING POWER INFORMATION AND SYSTEM OPERATION. POM PDU User Manual Ver. 1.0...
-
Page 9: Web Interface
5. Web Interface Login: Input the PDU IP address in web browser. Default ID is snmp. Password is 1234. POM PDU User Manual Ver. 1.0... - Page 10 Information: PDU Display total PDU and each outlet power consumption. When plug the option device - ENV probe, it will display temperature and humidity information. POM PDU User Manual Ver. 1.0...
- Page 11 Information: System Indicate PDU system information, including: Model No. Firmware Version MAC Address System Name System Contact Location POM PDU User Manual Ver. 1.0...
- Page 12 Select the outlet by checking the box and then click ON or OFF button to control output power for PDU ON: Press the icon to turn on the assigned outlets. OFF: Press the icon to turn off the assigned outlets. OFF/ON: Press the icon to reboot the assigned outlets. POM PDU User Manual Ver. 1.0...
- Page 13 Note: The outlet number needs to be input by the alphabetical order. ON: Press icon to turn on the assigned group. OFF: press icon to turn off the assigned group. Active: Enable it to be a controllable group. POM PDU User Manual Ver. 1.0...
- Page 14 Turn off outlet at this time None OFF/ON Turn off outlet at this time Turn on outlet at this time ON/OFF Turn on outlet at this time Turn off outlet at this time Active: Enable the assigned schedule control. POM PDU User Manual Ver. 1.0...
- Page 15 10 minutes have not obtained the response, the number will display 10 and PDU will carry out the assigned action automatically. Action: Select outlet action to “OFF” or “OFF/ON” Active: Enable this function. POM PDU User Manual Ver. 1.0...
- Page 16 Set the outlet name and delay time. Name: Rename the outlet. ON: Set delay time for power on sequential. OFF: Set delay time for power off sequential. Note: The maximum delay time is 255 seconds. POM PDU User Manual Ver. 1.0...
- Page 17 Configuration: Threshold Set the warning and overload threshold for each circuit. Set lower and upper threshold for temperature and humidity. POM PDU User Manual Ver. 1.0...
- Page 18 Configuration: User Change ID and password. Default ID is snmp and password is 1234. POM PDU User Manual Ver. 1.0...
- Page 19 Configuration: Network PDU network information Enable DHCP: Change the way to get IP address for PDU. POM PDU User Manual Ver. 1.0...
- Page 20 The message in the email: Indicate OutletA~H-XXXXXXXX status in order X=0 : means the power off. X=1 : means the power on. Note: Make sure DNS server can resolve the Email Server’s domain name. POM PDU User Manual Ver. 1.0...
- Page 21 When event occurs, PDU can send out trap message to pre-defined IP address. Trap Notification: Set receiver IP for trap. Community: Set SNMP community. Read Community is public and fixed. Default Write Community is “public” and can be modified by user. POM PDU User Manual Ver. 1.0...
- Page 22 Configuration: SSL Enable SSL for web communication. User must input the correct ID and password to enable SSL function. The ID and password must be the same with the setting in “User”. POM PDU User Manual Ver. 1.0...
- Page 23 Configuration: Time Set the time for schedule control. Internet Time Setting: Get time from the assigned network time server. System Time: Input time manually. POM PDU User Manual Ver. 1.0...
Need help?
Do you have a question about the POM PDU and is the answer not in the manual?
Questions and answers