Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS
PLEASE READ BEFORE YOU CONTINUE FURTHER
WARNING AND INSTRUCTIONS
GENERIC
•
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
•
DUE TO THE SIZE OF THIS PRODUCT WE RECOMMEND THAT IT IS ASSEMBLED IN THE
ROOM INTENDED FOR USE.
•
WHEN YOU ARE READY TO START,MAKE SURE THAT YOU HAVE THE RIGHT TOOLS,
PLENTY OF SPACE AND A CLEAN, DRY AREA FOR ASSEMBLY.
•
UNWRAP ALL PACKAGING MATERIALS AND PLACE THE COMPONENTS ON TOP OF
THE CARTON BOX OR ON A CLEAN FLOOR TO PREVENT IT FROM SCRATCHING.
•
CHECK THE PACK AND MAKE SURE YOU HAVE ALL THE PARTS LISTED.
•
ENSURE THAT THIS PRODUCT IS FULLY ASSEMBLED AS ILLUSTRATED BEFORE USE.
•
TOOLS NOT INCLUDED.
•
CHECK ALL SCREWS OR BOLTS ARE TIGHTENED AND INSPECT REGULARLY.
•
THIS PRODUCT SHOULD ONLY BE USED ON FIRM,LEVEL GROUND.
•
KEEP SMALL PART OUT OF REACH OF CHILDREN.
•
MAKE SURE THE LEGS REMAIN IN CONTACT WITH THE GROUND.
•
DO NOT USE POWER TOOLS TO CONSTRUCT THIS PRODUCT.
•
DO NOT TIGHTEN SCREWS UNTIL FULLY ASSEMBLED.
•
DO NOT OVER TIGHTEN SCREWS OR BOLTS.
•
DO NOT USE THIS PRODUCT IF PARTS ARE MISSING, DAMAGE OR WORN.
•
DO NOT SIT AND STAND ON THE PRODUCT.
•
TO CLEAN WIPE WITH A SPONGE AND WARM SOAPY WATER.DO NOT USE SOLVENT
BASED CLEANERS OR DETERGENTS AS THEY CAN BLEACH OR DAMAGE THE PRODUCT.
•
NEVER USE SCOURERS, ABRASIVES OR CHEMICAL CLEANERS.
CANYON SIDEBOARD
IMPORTANT
PAGE 1 OF 10
Advertisement
Related Manuals for GWF CANYON SIDEBOARD
Summary of Contents for GWF CANYON SIDEBOARD
- Page 1 CANYON SIDEBOARD ASSEMBLY INSTRUCTIONS IMPORTANT PLEASE READ BEFORE YOU CONTINUE FURTHER WARNING AND INSTRUCTIONS GENERIC • IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. • DUE TO THE SIZE OF THIS PRODUCT WE RECOMMEND THAT IT IS ASSEMBLED IN THE ROOM INTENDED FOR USE.
- Page 2 (Screwdriver not provided) Use a flat blade screwdriver to tighten the cam nuts.A quarter turn clockwise is all that is needed. This is how a cam nut works... The head of the bolt goes into the wide mouth of the cam nut. You then turn the nut so the narrow part closes over the bolt.
-
Page 3: Parts List
PARTS LIST MIDDLE RIGHT PANEL 1 PC BACK PLINTH HEAD DRAWER 2 PCS MIDDLE LEFT PANEL 1 PC BOTTOM PANEL 1 PC BOTTOM PLINTH 2 PCS MIDDLE BOTTOM PLINTH 2 PCS RIGHT SIDE PANEL 1 PC LEFT SIDE PANEL 1 PC BACK RIGHT LEFT PANEL 2 PCS MIDDLE BACK PANEL... -
Page 4: Hardware List
HARDWARE LIST 15x12 MM CAM NUT 36 PCS 6.5x36.5 MM CAM BOLT 36 PCS 18x5 MM COVER CAP 36 PCS 8x32 MM DOWEL 67 PCS 5x12 MM SHELF SUPPORT 8 PCS 14.5x19.5 MM NAILS 8 PCS OUTSIDE RIGHT DRAWER RUNNERS L=350 MM 3 PCS OUTSIDE LEFT DRAWER RUNNERS L=350 MM 3 PCS... -
Page 5: You Will Need
STEP 1 STEP 2 YOU WILL NEED : YOU WILL NEED : 8 PCS 16 PCS 8 PCS 8 PCS 4 PCS 22 PCS 3 PCS 3 PCS 18 PCS 4 PCS 3 O O Arrow to point in the direction of the hole Arrow to point in the direction of... - Page 6 STEP 3 STEP 4 YOU WILL NEED YOU WILL NEED 6 PCS 4 PCS 6 PCS 6 PCS 8 PCS 4 PCS 4 PCS Arrow to point in the direction of the hole Insert cam nuts (A) into pre-drilled holes and rotate the cam nut (A),so that the arrow Use flat head screwdriver to tighten cam nuts (A).Cover the cam nuts (A) with the points towards the inserted cam bolt (B).Use flat head screwdriver to tighten the cam cover cap (C) gently.Insert the back panels.
- Page 7 STEP 5 STEP 6 YOU WILL NEED : YOU WILL NEED : 8 PCS 2 PCS 10 PCS 10 PCS 2 PCS 7 PCS 6 PCS 1 PC Arrow to point in the direction of the hole Insert cam nuts (A) into pre-drilled holes and rotate the cam nuts (A),so that the arrow points towards the inserted cam bolt (B).Use flat head screwdriver to tighten the cam Insert cam bolt (B) into pre-drilled hole and fix with screwdriver.Use flat head nuts (A).Cover the cam nuts (A) with the cover cap (C) gently.
- Page 8 STEP 7 STEP 8 YOU WILL NEED : YOU WILL NEED : 6 PCS 6 PCS 8 PCS 6 PCS 18 PCS 3 PCS 3 PCS 6 PCS 12 PCS Arrow to point in the direction of the hole Insert cam nuts (A) into pre-drilled holes and rotate the cam nuts (A) so that the arrow Insert the shelf support (E) into the desired positions and insert the shelf panels and points towards the inserted cam bolts (B).Use a flat head screwdriver to tighten the drawer into the unit.
- Page 9 STEP 9 STEP 10 YOU WILL NEED : YOU WILL NEED : 4 PCS 16 PCS 22 PCS 22 PCS Take care to screw into the side and base panels at an angle to avoid piercing through Assemble 90 hinges (K) into the right & left doors with the screw (P).Attach the doors the back panel.This could cause damage to the back panel and be visible from the to the unit with a screwdriver.
- Page 10 STEP 11 Final Result THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE PAGE 10 OF 10...