Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trinnov Audio Amplitude8
Summary of Contents for Trinnov Audio Amplitude8
- Page 1 Amplitude8 USER MANUAL www.trinnov.com...
- Page 3 THANK YOU FOR CHOOSING TRINNOV AUDIO The Amplitude amplifier is among the most advanced available. By combining high-power linear power supplies and the Class D, N-Core NC-1200 amplifier modules, Trinnov Audio has ® delivered an amplifier that closely approaches the theoretical ideal: a straight wire with gain.
-
Page 5: Table Of Contents
CONTENT PREFACE CONTENT IMPORTANT SAFETY INSTRUCTIONS ABOUT THE AMPLITUDE 1.1 GETTING TO KNOW YOUR AMPLITUDE 1.2 BURN-IN TIME 1.3 SPECIFICATIONS 1.4 THE FRONT PANEL 1.5 THE REAR PANEL OPERATION 2.1 ENVIRONMENTAL NOTICE 2.2 REMOTE TRIGGERS APPENDIX A.1 TROUBLESHOOTING SOLUTIONS A.2 DB25 TASCAM PINOUT... -
Page 7: Important Safety Instructions
THIS UNIT CONTAINS VOLTAGES WHICH CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT OPERATE WITH COVERS REMOVED. REFER ALL SERVICING TO YOUR AUTHORIZED TRINNOV AUDIO DEALER. FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE FUSES ONLY WITH THE SAME TYPE AND RATING OF FUSES AS SPECIFIED. - Page 8 TO PREVENT DAMAGE TO THE ANALOG OUTPUT CIRCUITRY, BE being used to secure non-Trinnov Audio feet do not screw any CERTAIN NOT TO SHORT THE OUTPUT SIGNAL TO GROUND. deeper into the chassis than the original ones. The original ENSURE THAT YOUR AUDIO OUTPUT CABLES DO NOT HAVE screw is 1/4-20 by 1/2 and goes into the chassis 1/4 inch.
-
Page 9: About The Amplitude
ABOUT THE AMPLITUDE GETTING TO KNOW YOUR AMPLITUDE This Amplitude has been put through a rigorous and unique testing procedure that ensures that it will last for many years with minimal service requirements. This procedure includes the following: • All assembled circuit boards are given a thorough visual inspection and are then tested in a bench reference Amplitude •... -
Page 10: Specifications
SPECIFICATIONS POWER POWER REQUIREMENTS 117VAC, 15 Amp SLO-BLO main fuse; 230VAC, 8 Amp SLO-BLO main fuse; 50/60Hz Less than 1W at Standby; <80W at idle; 1500W maximum x 2 when fully loaded POWER CONSUMPTION 5-12 VDC; Steady State TRIGGER INPUT MODES /PROCESS Standby: Amplifier is ready to be turned on via front panel switch or remote trigger. -
Page 11: The Front Panel
Conventions: For clarity purposes, references to buttons and LED’s will be shown in bold capital letters. THE FRONT PANEL STANDBY BUTTON After the left-hand (when viewed from the front of the amplifier) rear-panel POWER switch is turned on, press the front panel STANDBY button to exit the standby mode. -
Page 12: The Rear Panel
THE REAR PANEL REMOTE TRIGGER OUTPUT MAIN POWER SWITCHES & Trigger out to rely to another device. (#11 is the Master Power Switch. Neither side of the amplifier will operate if this switch is set to off.) #1 controls the right-hand amplifier and disconnects AC to POSITIVE BINDING POST all circuits. -
Page 13: Operation
Damage to the Amplitude caused by improper operation, wiring and/or ventilation will not be covered under warranty and Trinnov Audio will not be liable for any consequential damage or loss. After the main rear power switches are turned on, the amp goes into Standby. The amplifier is completely off, save for a very small (and low power) supply to power the soft start circuit. -
Page 14: Appendix
APPENDIX TROUBLESHOOTING SOLUTIONS If the Amplitude should function abnormally during operation, please review the items in the following checklist. Please be sure to thoroughly check all other connected components such as speakers, preamplifiers, as well as cables. REMEDY SYMPTOM POSSIBLE CAUSE(S) No power or front panel lights and no sound. - Page 16 TRINNOV AUDIO Headquarters- 5 rue Edmond Michelet - 93360 Neuilly-Plaisance - FRANCE Phone: +33 (0)1 47 06 61 37 Email: sales@trinnov.com - www.trinnov.com...
Need help?
Do you have a question about the Amplitude8 and is the answer not in the manual?
Questions and answers