schanz Studio Star Setting Instructions Manual

Electronic motor

Advertisement

Quick Links

Setting Instructions
Electronic Motor
This Operating Instruction contains important safety instructions. For
the safety of persons it is important to follow these instructions.
This instruction should be kept.
Schanz Rollladensysteme GmbH
Forchenbusch 9
D- 72226 Simmersfeld
Tel.
+49 (0)7484/9291-0
Fax:
+49 (0)7484/ 9291-36
Internet: www.rollladen.de
Einstellanleitung Elektronikmotor-Studio Star_englisch.docx
-Studio Star-
Stand: 13.01.16
Seite 1 von 16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Studio Star and is the answer not in the manual?

Questions and answers

Summary of Contents for schanz Studio Star

  • Page 1 Setting Instructions Electronic Motor -Studio Star- This Operating Instruction contains important safety instructions. For the safety of persons it is important to follow these instructions. This instruction should be kept. Schanz Rollladensysteme GmbH Forchenbusch 9 D- 72226 Simmersfeld Tel. +49 (0)7484/9291-0...
  • Page 2: Table Of Contents

    Content Setting the drive into learning mode ............................3 1.1. Setting with test cable..............................3 1.2. Setting with micro switch and switch ..........................3 Setting Instructions - Type: S, GS, SI, SIG, R, G ........................4 2.1. Overview Off-Mode 1 – Only suitable for type S ......................4 2.2.
  • Page 3: Setting The Drive Into Learning Mode

    1. Setting the drive into learning mode 1.1. Setting with test cable Step No. Operation Note Check The motor is delivered in learning mode. If a fault occurs during the programming or if an already programmed drive should be installed in a different position or changes were made to the roller shutter, then the drive can be set again into learning mode.
  • Page 4: Setting Instructions - Type: S, Gs, Si, Sig, R, G

    2. Setting Instructions - Type: S, GS, SI, SIG, R, G The drive has 2 different switching modes, the selection takes place automatically via the setting. 2.1. Overview Off-Mode 1 – Only suitable for type S Upper end position about torque detection (shutter moves against the stop) / End position down after putting on the armor guided tour through the system detects that the winding shaft.
  • Page 5: Setting Off-Mode 1 (With Test Cable) - Only Suitable For Type S

    2.3. Setting Off-Mode 1 (with test cable) - Only suitable for type S (Upper end position about torque detection / End position down after putting on the armor guided tour through the system de- Automatic setting tects that the winding shaft) - Step No.
  • Page 6: Setting Off-Mode 1 (With Micro Switch And Switch) - Only Suitable For Type S

    2.4. Setting Off-Mode 1 (with micro switch and switch) - Only suitable for type S (Upper end position about torque detection / End position down after putting on the armor guided tour through the system de- Automatic setting tects that the winding shaft) - Step No.
  • Page 7: Setting Off-Mode 2 (With Test Cable) - For All Types With Box On Bottom

    2.5. Setting Off-Mode 2 (with test cable) – For all types with box on bottom Upper end position about torque detection / set end position bottom Step No. Operation Note Check Important: - First, there must always be taught the upper end position. - If the drive switches off due to a malfunction (too fast increase of force) before reaching the endpoint, it has to be set into learning mode again.
  • Page 8: Setting Off-Mode 2 (With Micro Switch And Switch) - For All Types With Box On Bottom

    2.6. Setting Off-Mode 2 (with micro switch and switch) – For all types with box on bottom set end position bottom) Upper end position about torque detection / Step No. Operation Note Check Important: - First, there must always be taught the upper end position. - If the drive switches off due to a malfunction (too fast increase of force) before reaching the endpoint, it has to be set into learning mode again.
  • Page 9: Setting Instructions - Type: Gu, Su, Gsu, Siu, Sigu, Ru

    Note: This mode is suitable only with solid shaft connectors and not for the Schanz special profile 3.2. Overview Off-Mode 2 – Standard for type GU Upper end position about torque detection (shutter moves against the stop) / set end position bottom.
  • Page 10: Setting Off-Mode 1 (With Test Cable)

    3.5. Setting Off-Mode 1 (with test cable) (Upper and lower end position about torque detection) - Automatic setting Step No. Operation Note Check Important: - First, there must always be taught the upper end position. - If the drive switches off due to a malfunction (too fast increase of force) before reaching the endpoint, it has to be set into learning mode again.
  • Page 11: Setting Off-Mode 2 (With Test Cable) - Standard For Type Gu

    3.7. Setting Off-Mode 2 (with test cable) - Standard for type GU (Upper end position about torque detection / set end position bottom) Step No. Operation Note Check Important: - First, there must always be taught the upper end position. - If the drive switches off due to a malfunction (too fast increase of force) before reaching the endpoint, it has to be set into learning mode again.
  • Page 12: Setting Off-Mode 2 (With Micro Switch Or Switch) - Standard For Type Gu

    3.8. Setting Off-Mode 2 (with micro switch or switch) - Standard for type GU (Upper end position about torque detection / set end position bottom) Step No. Operation Note Check Important: - First, there must always be taught the upper end position. - If the drive switches off due to a malfunction (too fast increase of force) before reaching the endpoint, it has to be set into learning mode again.
  • Page 13: Setting Off-Mode 3 (With Micro Switch And Switch)

    Step No. Operation Note Check Setting the lower end position Press DOWN-Button, until the lower end position is reached and the drive switches off, keep pressing the button for at least 1 sec. longer after switching off. The setting mode is exited. The learning of the forces happens automatically when running continuously from one end position to the other.
  • Page 14: Setting Off-Mode 4 (With Test Cable)

    3.11. Setting Off-Mode 4 (with test cable) (Set end Position at the top / set end position bottom) Step No. Operation Note Check Important: - First, there must always be taught the upper end position. - If the drive switches off due to a malfunction (too fast increase of force) before reaching the endpoint, it has to be set into learning mode again.
  • Page 15: Setting Mode 4 (With Micro-Switch Or Switch)

    3.12. Setting Mode 4 (with micro-switch or switch) (Set end position at the top / set end position bottom) Step No. Operation Note Check Important: - First, there must always be taught the upper end position. - If the drive switches off due to a malfunction (too fast increase of force) before reaching the endpoint, it has to be set into learning mode again.
  • Page 16: Copyright / References To This Documentation

    4. Copyright / References to this documentation The copyright (copyright ©) for the present documentation is being kept by Schanz Rollladensysteme GmbH as well as partial- ly by the suppliers of the sub vendor documentation. The containing information is solely designed for the operating companies of our roller shutters. It may not be changed, extend- ed, duplicated, saved on data linked institutions and spread without our written agreement nor should it be used for other pur- poses.

Table of Contents