Inventec FLY DS400 Manual
Structured disassembly sop
Hide thumbs
Also See for FLY DS400:
- Troubleshooting manual (15 pages) ,
- Maintenance instruction (51 pages)
Subscribe to Our Youtube Channel
Related Manuals for Inventec FLY DS400
Summary of Contents for Inventec FLY DS400
- Page 1 DG12BT(FLY DS400)_Structured Disassembly SOP Prepared by: LI, Rui-Yang Approved by: Sun, ban-li Publication date: Jul. 7, 2008...
- Page 2 1. Take up the mobile phone, disassemble this battery cover, and record the bad item. (Image A, Image B) ※ Notice: Inspect whether the label-waterproof and label-warning & Network Access License are broken, and replace the new one in time. label-waterproof label-warning Image A Image B Inventec Confidential...
- Page 3 Innovating Customer Value 2.Take off the Test Hole Cover from case-KT-bottom by tweezers. (image C) ※ Notice: Don’t scratch the Keyboard bottom. Take off the hole cover image C Inventec Confidential...
- Page 4 Innovating Customer Value 3. Take-down the 4 screws on the keyboard bottom by screwdriver (Image D) Image D Inventec Confidential...
- Page 5 ※Notice: Inspect whether the label-waterproof is broken, and replace a new one in time as requested. And then, Notice that avoid the left earphone and charger Jack when disassembling the keyboard bottom. earphone Cover Label-waterproof image E Charge jack Cover Inventec Confidential...
- Page 6 Innovating Customer Value 5. Take down the Side-Key. (image F) Side-Key Image F Inventec Confidential...
- Page 7 Innovating Customer Value 6. Tear off this Mylar of the motor, Disassemble the 2 screws on the Antenna. (Image G) Take down these 2 Screws Tear off this Mylar Image G Inventec Confidential...
- Page 8 FPC plug from the MB. (Image H) ※. Notice: the slice made of iron can’t be removed from the FPC plug, if true, the whole FPC need to be replaced. Image H Inventec Confidential...
- Page 9 Innovating Customer Value 8.Remove the KT, Motor, receiver, MIC , the conduction cushion from the top-case set (Image I) receiver Key-press Mylar KB FPC & EL set Image I Inventec Confidential...
- Page 10 Tear off shield Mylar, take apart the KB FPC and Dome sets, Unsolder the FPC by electric-iron (Image J) ※Notice: After taking apart the Dome, dip a little absolute alcohol by cotton stick to clean the PAD on the KB. KB FPC EL Dome Shield Mylar Image J Inventec Confidential...
- Page 11 Antenna from the MB (Image K) ※Notice: when removing the motor, stick the film onto the motor, or else, the motor should be replaced; avoid scalding the bracket of Antenna by electric-iron. Remove the motor at first Image K Inventec Confidential...
- Page 12 Innovating Customer Value 11). Take apart the SPK and the motor down-lead by electric-iron (Image L) Image L Inventec Confidential...
- Page 13 12). Tear off the foam on the side-key FPC buckle , and then remove the camera, Side-Key FPC set, tear off the conduction cushion (Image M) Camera Camera holder foam SUPPORT the conduction cushion of FPC Side-Key FPC Sets the conduction Image M cushion of shied Inventec Confidential...
- Page 14 13. Take apart the bracket of GSM antenna and SPK sets. (Image N) ※Notice the direction of removing the LCM FPC connector to prevent damaging the connector. the bottom cover of the bracket of antenna Speaker Image N Speaker foam Inventec Confidential...
- Page 15 Mylar of the FPC, and then take off the foam of the earphone (image O) ※Notice: the function of the Mylar is to isolate the electrostatic, if being torn off, it needs to be replaced. Mylar the foam of the earphone Image O Inventec Confidential...
- Page 16 Innovating Customer Value 14. Take apart the LCD from the MB (Image P) ※Avoid riving the LCD Pin when removing the LCD. Image P Inventec Confidential...
- Page 17 Innovating Customer Value 15. Take apart the GSM Sub-Module Shielding Cover from the MB (Image Q) The GSM Sub-Module RF shielding cover image Q The GSM Sub-Module BB shielding cover Inventec Confidential...
- Page 18 Innovating Customer Value 16. Take apart the GSM Main-Module Shielding Cover from the MB (Image P) Main-Module The GSM RF shielding cover The GSM Main-Module BB shielding cover Image O Inventec Confidential...
- Page 19 Innovating Customer Value ADD： ** Please reverse operate according to the order when assemble. ** Please according to the repair scale when dismantle. (consult spare parts list) The End Inventec Confidential...
Need help?
Do you have a question about the FLY DS400 and is the answer not in the manual?
Questions and answers