Summary of Contents for Minnich M-BOX
- Page 1 Minnich M-BOX Minnich Manufacturing Contact 1444 ST RT 42 Phone: (419)-903-0010 Mansfield,OH 44903 Email: sales@minnich-mfg.com...
-
Page 2: Table Of Contents
Chapter 2-................................14 Operation Instructions..........................14 Notes...............................15 Warranty..............................16 Parts Ordering Online...........................17 It is Minnich’s policy to constantly strive to Your new Minnich M-BOX was carefully improve our products. The information, spec- designed and manufactured to give years ifications, and illustrations in this publication of dependable service. -
Page 3: General Warnings
Water should be used for dust suppression when wet cutting is feasible. When the hazards from inhalation of dust, mist and fumes cannot be eliminated, the operator and any bystand- ers should always wear a respirator approved by NIOSH/MSHA for the materials being used. M-BOX Manual... -
Page 4: General Safety
Indicates a hazardous situation witch, if not avoided, COULD result in DEATH or SERI- OUS INJURY Indicates a hazardous situation witch, if not avoided, COULD result in MINOR or MOD- ERATE INJURY Addresses practices not related to personal injury M-Box Manual... - Page 5 ∆ Never use accessories or attachments that are ∆ NEVER operate this equipment without not recommended by Minnich for the equip- proper protective clothing, shatter proof ment. Damage to the equipment and/or injury glasses, respirator protection, hearing pro- to user may result.
- Page 6 Use only ∆ ALWAYS keep vibrator motor clean for bet- Minnich Recommended replacement parts. ter and safer operation. ∆ When applicable, use a protection wiring de- ∆ ALWAYS store equipment properly when vice such as a Ground Fault Circuit Interrupter, it is not being used.
- Page 7 ∆ Disconnect the plug from the power cord source and/or the battery pack from the power tool before making any adjustments, chang- ing accessories, or storing power tools. Such preventative safety measures reduce the risk of starting the power tool accidentally. M-BOX Manual...
- Page 8 ∆ Fix damage to machine and replace any bro- ken parts immediately. ∆ ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel. M-Box Manual...
- Page 9 To find the latest revision of this publication, short circuit. visit our website at: www.minnich-mfg.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES. Specifications and part numbers are subject to change without notice.
-
Page 10: General Specifications
GENERAL SPECIFICATION M-BOX INPUT SOURCE OUTPUT source Volts Phase Single Three Hertz 50/60 Hz 6,000 VPM 100Hz 8,000 VPM 133Hz 10,000 VPM 180Hz 10,800 VPM Amps 15 Minimum 10.5 Maximum M-Box Manual... -
Page 11: Safety Decal Location
SAFETY DECAL LOCATION All safety labels on Minnich Manufacturing units have been carefully placed so they can be easily seen at all times. There are several different types of labels on the units. Always keep these warnings free of dirt, concrete, or anything else that restricts visibility. - Page 12 PRIOR TO OPERATION Read and understand all safety, operating and maintenance instructions before using this product. MODEL M-BOX VOLTS 230 AC CYCLE PHASE 6000 / 8000 / 10,800 COMPONENTS MAY BE ENERGIZED EVEN...
- Page 13 PRIOR TO OPERATION Read and understand all safety, operating and maintenance instructions before using this product. MODEL M-BOX VOLTS 230 AC CYCLE PHASE 6000 / 8000 / 10,800 COMPONENTS MAY BE ENERGIZED EVEN...
-
Page 14: Chapter 2
OPERATION INSTRUCTIONS Starting Procedures ∆ Make sure M-Box on/off switch is in the OFF position The M-box converter is designed to run (2) ∆ Make sure vibrator switch is in the OFF position individual 230v; 3phase concrete vibrators with 100 feet of extension cord on each ∆... -
Page 15: Notes
NOTES M-BOX Manual... -
Page 16: Warranty
The product must have been purchased resulting from the installation or removal of this directly from Minnich or from an authorized product from any installation, any unauthorized Minnich reseller. tampering with this product, any repairs at-... -
Page 17: Parts Ordering Online
Scan for Helpful Videos! WE ACCEPT THE FOLLOWING CARDS! NON-DEALER AND INTERNATIONAL COSTUMERS: Contact Minnich Manufacturing through the following num- ber to locate a dealer near you. (419-903-0010) All orders are treated as Standard Orders and will ship the same day if received prior to...
Need help?
Do you have a question about the M-BOX and is the answer not in the manual?
Questions and answers