Advertisement
®
2.
Charging Bluetrek
S2
Your headset is delivered uncharged. So before the first use, you must fully recharge it
for about 8 hours with the supplied charger, until the blue indicator light turns on. The
use of any other charger will automatically suspend the warranty. During subsequent
charges, the charging should take approximately 1 hour 45 minutes.
Please connect the charger to the headset and to the mains. During the charge, the
indicator light is either red if your headset battery was excessively discharged, or purple
during a normal charge. The indicator light will turn to blue when the charge is
complete.
When you hear a light beep in your headset at regular intervals, and the indicator light
flashes in red, your headset needs to be recharged.
To maximize battery lifetime, it is recommended to recharge your headset to full
capacity only when the battery is low, since a battery has a lifetime of about 500
charging cycles.
If you leave your headset battery empty for an extended period of time, it could
excessively discharge the battery. In this case, you may have to charge your headset
for 10 hours or more until the battery recovers and recharges completely. The indicator
light will be red at the beginning of the charge to recover the battery capacity, then it will
turn to purple for the normal charging process.
Only switch on the headset once the blue indicator light turns on, indicating the battery
has fully recovered.
Do not let the battery charger remain plugged in the headset for more than 24hours.
®
3. Pairing Bluetrek
S2
®
Before using the Bluetrek
S2 headset, you must pair it with your Bluetooth
phone. Pairing is the process of linking 2 Bluetooth
communicate.
Pairing only needs to be done once. When moving out of the range (10 meters) or
switching off the headset and then on again, press the TALK button on the headset to
®
reconnect the Bluetooth
link. If you pair your Bluetooth
®
Bluetooth
device, you will have to pair the Bluetrek
use. The Headset and Hands-free profile is automatically selected by the mobile phone
during pairing.
®
IMPORTANT : Before pairing, all Bluetooth
To initiate the pairing, put both the headset and the mobile phone within 0.3 meter (1
foot) from each other. Make sure there is no Wi-Fi equipment operating in the vicinity.
1. Switch on your phone and select the Bluetooth
®
phone (Consult your Bluetooth
mobile phone user guide).
2. Press and hold (do not release it) the TALK for about 7 seconds until the
indicator light flashes red and blue alternately. Then release the TALK button.
PAGE 3 / 6
®
mobile
®
devices, so that they can
®
mobile phone with another
®
S2 with your phone again before
devices must be switched off.
®
discover mode on the Mobile
3. Once the mobile phone detects the headset, a message is displayed containing
the name of the headset "BLUETREK-S2".
4. Follow the phone instructions to accept the pairing. The PIN code (or passkey) is
0000.
5. When the pairing is completed, the indicator light will switch to blue, and flashes
slowly.
If you haven't started the discovery mode within 5 minutes, the headset will go to the
standby mode. You must then switch off your headset and start the pairing again.
®
A very limited number of Bluetooth
process than the one explained above. If you encounter any difficulties to pair your
headset with your mobile phone, visit our website www.bluetrek.com or consult your
dealer.
®
4. Wearing Bluetrek
S2
The headset can be worn on either ear by rotating the ear clamp. Make sure the
speaker is properly inserted into your ear.
®
5. Switching Bluetrek
S2 ON and OFF
®
Switching Bluetrek
S2 ON
When your headset is off, press and hold the TALK button for about 2 seconds until the
blue indicator light is on. A beep can be heard in the speaker. Release the TALK
button.
®
Switching Bluetrek
S2 OFF
When you headset is on, press and hold the TALK button for about 5 seconds until the
red indicator light flashes. A beep can be heard in the speaker. Release the TALK
button.
To save power, the blue indicator light flashes at long intervals. To check if your
headset is ON, press shortly on the TALK button. If the indicator light is blue, it means
your headset is ON.
6. Making a call
Note: The voice dialling feature is not available on all mobile phones or PDAs. However
you can always dial directly on your keypad. If your mobile phone does offer the voice
recognition feature, you can make a call directly from the headset without touching
your Bluetooth
®
mobile phone.
Mobile phone with voice recognition
. Make sure the voice dialling functions on your phone is activated and your voice tags
have been recorded. To program these, please refer to your phone manual.
. Press the TALK button shortly (when there is no incoming and no active all). An audio
connection is established.
. Wait for the audio signal sent by the mobile phone (generally a short tone).
PAGE 4 / 6
mobile phones require a different pairing
Advertisement
