Summary of Contents for aci GRIFFIN
- Page 1 & R WNERS ANUAL EFERENCE UIDE Serial Number: Date Purchased: Dealer: AIR CONCEPTS INDUSTRIES U. S. Patent No. 5,063,905...
-
Page 2: Table Of Contents
• The compressed air source used with the Griffin can cause serious injury or death. Air Source Installation............4 • Sale or use of the Griffin is not intended for individuals under the age of 18. Seating of Air Source............4 • The Griffin is to be used only as described in this manual. -
Page 3: Specifications
SPECIFICATIONS ALIBER ARREL • 0.68 Paintballs Only • Aircraft Quality Aluminum • Microhoned and Polished LOWBACK AUTOMATIC OWERED • Muzzle Break • Compressed CO2 45 G IECE RIGGER RAME • Regulated Compressed Air • Regulated Nitrogen • Ergonomic “Point And Shoot” Design •... -
Page 4: Operation
To cock the Griffin, pull the cocking pin rearward until it latches. during the last 1/2 turn. Over tightening can damage the Griffin. Be careful, if you let go before it latches, the Griffin can fire. DO If a leak persists, replace the bottle O-ring. -
Page 5: Loading
The trigger safety must be off; that is to the left. Fire the Griffin as often as you like with air, with or without paintballs in it. This helps break it in and makes it operate smoother. -
Page 6: Tuning Your Gun
TUNING YOUR GUN CAUTION Regular tuning is essential. But don’t waste time trying to tune a Do not adjust velocity with the striker plug gun which is: partially unscrewed. If it is later screwed back • Dirty or poorly lubed in, the velocity may be dangerously high. -
Page 7: Field Maintenance
FIELD MAINTENANCE Before each use, your gun must be cleaned, lubed, and tuned. Field Stripping To field strip your gun (refer to illustrations): 1. Depressurize gun (remove air source) 2. Unload gun. 3. Uncock gun. 4. Unscrew barrel. 5. Unscrew bolt plug. 6. -
Page 10: Maintenance
Field strip as described on page 7 and use warm soapy water or rubbing alcohol where needed to clean the rest of your Griffin. The following parts should not be removed for Remove the bolt O-rings to remove paint and dirt build up from routine maintenance: the O-ring grooves. -
Page 11: Cleaning Schedule
CLEANING SCHEDULE SERVICE HINTS Every 500-1000 shots • Lubricate with AIRLUBE Bolt Pin A nylon pin in the bolt prevents movement when the gun is fired. Every 1-3,000 shots • Remove bolt If the cocking pin is loose, replace the nylon pin (supplied) by •... -
Page 12: Trouble Shooting Hints
TROUBLESHOOTING Half the guns sent in for repair are dirty, poorly lubed, or have a damaged Velocity is very erratic (>20 fps between shots): striker O-ring Check these items first. • O-rings on bolt or striker are nicked or torn - install new ones. •... - Page 13 • Reservoir plug O-ring defective - replace. • Bottle valve releases gas during more than last 1/2 turn of bottle instal- • Valve body was disturbed - call your dealer or ACI for possible service. lation, stressing O-ring - try a different bottle.
- Page 15 Vertical Bottle Adapter....17 Velocity Pin O-ring......54 Vertical Adapter Bolt.......18 Striker Plug........55 Gun To Hose Adapter.....19 Striker Plug O-ring......56 8.5” Stainless Steel Hose With JIC Bolt Plug O-ring......57 Fitting..........20 Bolt Plug.........58 Front Frame Screw......21 Griffin Receiver.......59 Front Bottomline Screw....22 Connecting Pin.......60...
-
Page 16: Warranty Information
This Concepts Industries, Inc., nor to any parts made defective by accident, is why sale of the Griffin is limited to individuals 18 years of age and misuse, abuse, or modification.