Advertisement
Quick Links
Advertisement
Related Manuals for FLI LOADED 900S
Summary of Contents for FLI LOADED 900S
- Page 1 FL900s-F1...
- Page 2 All content included in this manual such as text, graphics, logos, icons, images data, the selection and arrangement thereof, are the property of FLI Audio (herein referred to as "FLI", "us" or "we") and its affiliate or their content and technology providers, and are protected by United Kingdom and International copyright laws.
-
Page 3: Table Of Contents
INSTRUCTION & INSTALLATION MANUAL CONTENTS Mounting Guidelines......Connections........... Setup Section........Applications..........7,8 Trouble Shooting........Specification........... 10 Warranty..........10 Accessories..........11... -
Page 4: Mounting Guidelines
Thank you for purchasing this FLI amplifier. It will provide you with a lifetime of trouble free use providing you follow a few simple guidelines. Mounting Guidelines Your FLI amplifier is designed with a swift installation routine in mind. Please mount the amplifier in a dry location on a solid surface. NEVER mount the amplifier upside down, this will cause the amplifier to over heat and will eventually damage the amplifier. Before fixing the amplifier in place please ensure that there is sufficient air flow around the exterior of the casing, at least two inches will be sufficient. Connections Power Cable At least an 8 gauge cable should be used for both the power and the ground connections to the amplifier. ● The power cable should be taken directly from the battery. Rubber grommets should be used when passing through any ● bulkheads to prevent the cable from becoming chaffed or cut. It is vital that a fuse / circuit breaker (of at least equal value to the one fitted on the amplifier) is placed in line with the ... - Page 5 Ground Cable The ground cable needs to carry the same current as the power cable. At least an 8 gauge cable should be used. ● The amplifier ground should be connected directly to the chassis of the vehicle, to bare metal. ● The cable length should be kept to an absolute minimum. ● (NB) It is not recommended that you connect the ground cable to the vehicles seatbelts anchor point. Remote Turn On A minimum of 18 gauge cable should be used for this connection. ● The cable should be run with exactly the same care and attention as the power cable and taken back to the source ● (headunit) and joined to the remote cable provided. If the source (headunit) does not have a remote turn on cable then a 12v supply should be used. This will require a ● switch to be fitted inline to enable the amplifier to be turned on and off. Remember that if this switch is left on you will flatten the car battery. RCA Cables Depending on the model number of your amplifier and the number of speakers you wish to power you will have to run ● either one or two RCA cables from the source to the amplifier. Please take extra care when running these cables from the source to the amplifier. Ensure that they are placed away ● from all items that can generate any interference, wiring harnesses etc. It is recommended that the RCA cables should be run on the opposite site of the car to the previously installed power ● cables, if possible. Low Level Input For connection to any source (headunit) with a low level output. This is your RCA output from the source (headunit). High Level Input To be used when no RCA’s are available. Use the provided loom to connect to closest speakers. The loom provided will only fit one way round. Once plugged in you should connect the wires this way around:...
- Page 6 This remote can be mounted in the front of the car and will give you the ability to raise the bass boost of the amplifier remotely in the range of 0 to +12 dB. They can be purchased separately from the FLI website www.fliaudio.co.uk, see back page for more details. Channel 3 / 4 Gain Control Used to match the input signal of the source (headunit) to the amplifier.
-
Page 7: Applications
Applications... - Page 8 Applications...
-
Page 9: Specification
Specification RMS Power @ 13.8v DC Power @ 4 Ohms stereo 4 x 100 watts RMS Power @ 4 Ohms bridged 2 x 225 watts RMS MAX power 900 watts Minimum speaker impendence 2 Ohms THD Distortion 0.2% IMD Distortion 0.2% Frequency Response 20Hz - 20 Khz... - Page 10 Specification RMS Power @ 13.8v DC Power @ 4 Ohms stereo 4 x 100 watts RMS Power @ 4 Ohms bridged 2 x 225 watts RMS MAX power 900 watts Minimum speaker impendence 2 Ohms THD Distortion 0.2% IMD Distortion 0.2% Frequency Response 20Hz - 20 Khz...
- Page 11 FLI embroidery logos on front and back FLI Tshirts Our heavy weight FLI T-shirts are a must have! Featuring small FLI logo on front and big logo on back. All sizes available FLI Stickers FLI stickers available in white or silver 5” 10”...
-
Page 12: Accessories
Accessories can be ordered separately from the www.fliaudio.co.uk FLI website Only available in the UK If out side uk please contact your dealer or distributer from the FLI website Stores FLI Power Capacitor added power The FLI powercap, a 1 farad, high...