1. Manuals
  2. Brands
  3. AKA Manuals
  4. Paintball equipment
  5. EXCALIBUR
  6. Operator's manual

AKA Excalibur Operator's Manual

Hide thumbs Also See for Excalibur:
Table of Contents

Advertisement

Quick Links

Download this manual
Warnings and Important Safety Guidelines
Warning! The Excalibur paintball marker is not a toy!
Careless or improper use, including failure to follow
instructions contained within this manual, may result in
injury or death.
Read Operator's Manual before use and comply with all
safety instructions. Do not fire this, or any marker, at a
person when at a close range. Observe all local laws,
regulations, and ordnances when using this marker. Use
only at paintball fields where safety codes are strictly
enforced.
You must be at least 18 years of age to purchase this
marker. Users under the age of 18 must do so only
under adult supervision. Use only bottles approved for
Nitrogen, compressed air, or CO2. Make sure all bottles
are hydro-tested according to DOT regulations.
Use only .68 caliber paintballs in this marker. Do not
attempt to fire foreign objects from this marker. Use an
approved barrel blocking device when your marker is
not in use. Always disconnect air source and switch off
power source when not in use. Never shoot at velocities
in excess of 300 FPS. Never put your fingers or foreign
objects in the feed tube of the marker.
Never expose battery to open flame or heat source.
When connecting or disconnecting the battery, take care
not to short out the battery.
Always wear eye protection when adjusting, servicing,
or using your marker. When doing any work to your
maker, make sure the power and air source have been
disconnected. Be sure all paintballs have been
removed. Seek professional assistance if you unsure
of anything.
Operator's Manual

Table of Contents

Schematics
Excalibur
2
2
3
3
4
4
4
5
6
7
7
7
8
10
10
10
11
13
13
14
16
16
17

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Excalibur and is the answer not in the manual?

Questions and answers

Related Manuals for AKA Excalibur

Summary of Contents for AKA Excalibur

  • Page 1: Table Of Contents

    Operator’s Manual Warnings and Important Safety Guidelines Table of Contents Introduction Warning! The Excalibur paintball marker is not a toy! Careless or improper use, including failure to follow Specifications instructions contained within this manual, may result in injury or death.

  • Page 2: Introduction

    Model: Excalibur(tm)(pat pend) The ground work for the very first ideas of the Excalibur Version:1300-B Caliber: .68 were laid down back in 1988 as I was working on my...

  • Page 3: Power Source

    **When using CO2 it is a MUST that you keep liquid CO2 out of the Excalibur(tm)(pat pend).** If running CO2 on the Excalibur(tm)(pat pend) you must use a tank with an anti-siphon tube. It is best to double regulate by using a secondary regulator attached to the Air Supply bottom of the grip.

  • Page 4: Excalibur Notes

    90 to 100 psi. Once the Excalibur has had Excalibur Notes a few cases of paint through it you can adjust the pneumatics reg down around 70 to 80 psi. AKALMP is continuosly refining the Excalibur to push its performance to the extreme.

  • Page 5: Cleaning And Maintenance

    Recommended lubricants: Extreme-lube from AKALMP If the Excalibur(tm)(pat pend) is to be stored for more or Palmer Pursuits paintball gun oil. then two months, remove the valve spring. This will increase the spring’s lifespan. It is a good idea to do...

  • Page 6: Troubleshooting

    Is the battery fresh and new? Troubleshooting - See Power Supply. Excalibur(tm)(pat pend) will not fire Is there a battery in the Excalibur(tm)(pat pend)? Firing too slow - See Power Supply. Is your rate of fire (ROF) set correctly? Is there air/nitrogen or CO2 gas present? - See Electronics.

  • Page 7: Custom Work

    Replacement of ball detent: When doing custom mill work to the body of the Excalibur be aware there are a few area that you should The ball detent may become worn or broken over time. stay away from and a few areas that have critical depths.

  • Page 8: Electronics

    Electronics the firing parameters. The Excalibur(tm)(pat pend) is controlled by a state of The factory settings for the Excalibur(tm)(pat pend) make the art software driven computer board. The newer design the gun run at 10 BPS (balls per second).
  • Page 9 This will reduce the movement of To change the firing parameters of the Excalibur(tm)(pat the battery and keep the wires from getting damaged.

  • Page 10: Hammer

    To pull the hammer cartridge out of the marker: Use a 5/ 32 allen wrench and unscrew the hammer cartridge. Urethane bumper Then gently pull it out the back of the Excalibur(tm)(pat pend). Hammer tube Use the hammer spanner wrench and an allen wrench -015 o-ring to loosen the hammer endcap.

  • Page 11: Other Component Parts

    Angel feed tubes. 1. De-gas the marker. The Excalibur uses a short feed tube that does not have 2. Unscrew the hammer cartridge from the back of the any problems feeding paint at a high rate of fire as long marker.
  • Page 12 The pneumatics regulator controls the air pressure fed 1. Using the pneumatics reg. removal tool, unscrew the to the solenoid valves, which in turn operate the rest of pneumatic reg from the front of the Excalibur(tm)(pat the gun. The maximum operating pressure of the pend).

  • Page 13: Pnematics Ram

    -113 is in use. Do not over-tighten the pin. Excalibur Screws & Pins: **Be careful not to damage the ram piston o-ring Serial # 0 to 57. when you re-install the ram shaft into the ram Quanity....Type...

  • Page 14: Sidewinder Regulator

    1....8-32 x .437 set screw (trigger stop) The Sidewinder(tm)(Pat Pend) regulator was designed 1....6-32 x .250 set screw (trigger stop lock) specificaly for use on the Excalibur(tm)(pat pend) 1....10-32 x .375 button head (grip plate/frame) because of its extremely low operating pressure of 4....4-40 x .5 button head (solenoid valves)
  • Page 15 -017 o-ring -015 o-ring When using CO2 it is a must that you keep liquid CO2 Regulator body middle out of the Excalibur(tm)(pat pend). -008 o-ring Regulator piston Disassembly of Sidewinder(tm)(pat pend) -113 o-ring...

  • Page 16: Solenoid Valves

    / Leads Metal Products Inc. There is no difference in shooting 2750 cases of paint if the cases were 2000rd the cost of the Excalibur(tm)(pat pend) for single or double boxes each. One randomly picked valve cycled over trigger frames. The two style of frames can be inter- changed without any modifications to the gun.

  • Page 17: Tornado Valve

    Valve Body -015 o-ring Tornado Valve The valve used in the Excalibur(tm)(pat pend) is also used in the Merlin body kits and other future markers. The valve is a bigger, stronger Tornado(tm)(pat #5791328) valve which was orginally designed for the cockers. The...

Table of Contents