MEGABLEU CHASE ZURG Playing Instructions

Advertisement

Quick Links

PLAYING INSTRUCTIONS

1. Synchronisation of the projector and gun

- Switch the ON-OFF switch located at the bottom of the projector
to "ON".
- Activate the gun by pressing the fire trigger. LCD screen will light
up (a firm red light will burn and the counter should say '00').
Note: the gun turns itself off after 60 seconds. To enable the gun you
have to press the fire trigger (there is no ON-OFF switch for the gun).
Reload button
LCD-display
which shows
how many
ZURG heads
you hit
- Select difficulty level of playing by
pressing one of the difficulty buttons: I, II or III.
- Buzz Lightyear's arm will flash and will project a red image of
ZURG on the wall or ceiling of the room. Aim the gun to ZURG and
press the fire trigger.
- The gun now synchronises itself with the projector and will beep
twice.
- Buzz Lightyear will start to turn and the gun will make different
sound effects. From this point the game can start.

2. Speed of the game

The speed at which the images appear gets determined by the buttons
located at the base of Buzz Lightyear:
I = (easy) II = (Average) III = (Difficult).
Fire trigger

3. Shooting ghosts

Buzz Lightyear turns around to project ZURG heads on the wall or
ceiling one by one.
The player has to aim his gun at ZURG and press the fire trigger to hit
ZURG before he disappears. If ZURG has been hit, the gun will produce
a sound and will register 1 point.

4. Reloading the gun

The gun has a total of 6 shots. After 6 shots you need
to press the reload button at the top in order to load
another 6 shots and continue the game (reload
button).

5. End of a shooting session

Buzz Lightyear will continue to project ZURG images for
approximately one and a half minutes. Players need to
shoot as many ZURG heads as they can. After one and
a half minutes, both the gun and Buzz Lightyear will
stop. The number of ZURG heads shot by the player is
shown on the LCD display on the gun. You can reset the
counter back to zero by pressing the trigger.
I

6. Playing a new game

II
To start a new game you have to push one of the difficulty buttons
III
located on Buzz Lightyear and synchronise again as described in part
one.

7. Ending the game

If you decide to end the game, switch the ON-OFF switch of Buzz
Lighthyear to OFF. You do not need to turn off the gun. It will turn itself
off after 1 minute.
Each player plays the game in turn.
At the beginning of each game the player has to synchronise the gun
and the projector before a new game can start.
The one who shoots the most ZURG heads is the winner.
Note: to determine the winner it is also possible to:
- set a certain score everyone has to reach (eg. 100 points).
- play different shooting sessions (eg. 3) and aim for the highest score.
2 PLAYERS OR MORE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CHASE ZURG and is the answer not in the manual?

Questions and answers

Summary of Contents for MEGABLEU CHASE ZURG

  • Page 1 PLAYING INSTRUCTIONS 3. Shooting ghosts Buzz Lightyear turns around to project ZURG heads on the wall or ceiling one by one. 1. Synchronisation of the projector and gun The player has to aim his gun at ZURG and press the fire trigger to hit - Switch the ON-OFF switch located at the bottom of the projector ZURG before he disappears.
  • Page 2 Put out the lights (or shut the curtains) until the room is sufficiently dark. © Disney/Pixar - Visit the Toy Story website at toystory.com Manufactured in China by MEGABLEU. All rights reserved. Do not play in a room which has a glass wall.

Table of Contents