Advertisement
Battery Replacement and Sensor
When the battery runs out
When the battery runs out,
will blink simultaneously. If you see this, replace
the batteries.
[Please use AA alkaline batteries] (Do not use
manganese batteries or rechargeable batteries)
When replacing the batteries, allow 20
seconds with the batteries removed, and
then insert the new batteries.
symbol will be reset and disappear.
# CAUTION
• Risk of fire or explosion if the battery is replaced by an incorrect type. Ensure to replace only with the same type.
• Risk of fire, explosion or the leakage of flammable liquid or gas if the battery is left in an extermely high temperature
surrounding environment and/or subjected extremely low air pressure. The battery pack or batteries shall not be exposed to
excessive heat such as sunshine, fire or the like.
• Risk of fire, explosion or the leakage of flammable liquid or gas if the battery is disposed into fire or a hot oven, recharged,
shorted, mechanically crushed or cut of the battery.
• If spilled fluid comes in contact with your eyes or on clothing, immediately rinse with water and consult a physician.
Declaration of Conformity with regard to the EMC
Directive 2014/30/EU
Declaration of Conformity with regard to the
RoHS Directive 2011/65/EU
Manufacturer:
JVCKENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi,
Kanagawa, 221-0022, JAPAN
EU Representative:
JVCKENWOOD Europe B.V.
Amsterdamseweg 37, 1422 AC Uithoorn,
THE NETHERLANDS
Declaration of Conformity with regard to the
Electromagnetic Compatibility Regulations
2016 (S.I. 2016/1091)
Declaration of Conformity with regard to the
Restriction of the Use of Certain Hazardous
Substances in Electrical and Electronic Equipment
Regulations 2012 (S.I. 2012/3032)
Manufacturer:
JVCKENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi,
Kanagawa, 221-0022, JAPAN
UK Importer:
JVCKENWOOD U.K. Limited
12 Priestley Way, London, NW2 7BA,
UNITED KINGDOM
and the red LED
Product Specifications
Power supply
Battery life
Operating temperature 0 °C to 35 °C (no condensation)
Storage temperature
External dimensions
Mass / Weight
Main materials
Detection method
Display method
Sensor life
Accessories
* The contents and specifications are subject to change without notice.
Troubleshooting
Cannot turn on
Error display "---"
The measured value is
not stable.
Getting an alcohol
reaction even though
not drinking.
No alcohol reaction
even though drinking.
About the "SENSOR EXCHANGE" indicator
When you use this product more
than 5,000 times, the "SENSOR
EXCHANGE" mark blinks.
Since the measurement accuracy of
the sensor will not be maintained,
it is recommended to replace this
product.
• Even if it is used infrequently, it is
recommended to replace it with a
new one after using it for one year.
DC 3 V two AA alkaline batteries
About 1,200 times
-10 °C to 60 °C (no condensation)
122 x 45 x 21 mm
Approximately 92 g (including batteries)
Body case: ABS resin
Semiconductor gas sensor
LCD digital display 0.00 mg/L and 0.05 mg/L to 1.00 mg/L
(If less than 0.05 mg/L, 0.00 mg/L will be displayed)
LED 2-stage display (Green/Red)
Purchased and used 1 year or 5,000 times
Instruction manual (warranty), attachment, strap,
Two AA alkaline batteries
Are there batteries?
† Set two AA alkaline batteries (included) correctly.
Is the plus/minus of the battery set in reverse?
† Please set plus and minus correctly.
Are you blowing properly? Is there any odor or gas at the
measurement location?
† Please refer to "How to use" in this manual and
measure correctly.
Are you using it in a windy place or a place with a strong
odor?
† Please change the location and measure.
Is there any odor remain inside the product?
† Shake this product lightly 2-3 times.
Are you measuring immediately after using mouthwash
or smoking ?
† Please refer to "Understanding Breath Alcohol Tester"
in this manual .
The blown breath may not have passed through the
sensor part.
† Refer to step 4 of "How to use" in this manual, and
blow properly.
Advertisement
