Summary of Contents for Toro Mauser KS-534 Full Safety Cab
- Page 1 Form No. 3395-604 Rev A Air Conditioning Kit Mauser KS-534 Full Safety Cab Model No. 02891 *3395-604* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Refer to the traction unit and cab Operator’s Storage ................10 Manuals for additional information. Schematics ..............11 You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product. Whenever you need service, genuine Toro parts, or additional... -
Page 3: Safety
• Always allow the air-conditioning system to cool down before working on any part of it. To ensure optimum performance and continued safety certification of the machine, use only genuine Toro... -
Page 4: Product Overview
Product Overview g0 1841 4 Figure 2 Evaporator, heater, and fans—mounted in front of the cab roof 1. Air conditioner: evaporator, heater, and double radial blower 3. Expansion valve 2. Heater valve g018399 Figure 3 Compressor—mounted on the engine... -
Page 5: Controls
g018436 Figure 4 Condenser and dryer/filter—mounted in rear of the cab roof 1. Condenser 3. Pressure switch 2. Dryer/filter Controls The controls are mounted on the right side in the roof lining. G025784 Figure 5 1. 3-position switch for 3. Air-conditioner switch radial-blower speed 2. -
Page 6: Specifications
Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories. To best protect your investment and maintain optimal performance of your Toro equipment, count on Toro genuine parts. -
Page 7: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Check all connections for tightness. After the first 100 hours • Check the refrigerant level. Every 50 hours •... -
Page 8: Checking The Refrigerant Pressure
Readings Always use genuine Toro spare parts when repairing or During the compression test, deviations from the values in servicing the air-conditioning system. -
Page 9: Checking The Compressor Magnetic Clutch
3. Check the level after this period and top up is necessary. Note: The occasional air bubble is acceptable. Checking the Compressor Magnetic Clutch Service Interval: Every 250 hours The compressor magnetic clutch is operating correctly if it clicks when it is turned on (Figure g019083 Figure 8... -
Page 10: Locating The Fuses
Storage Refer to the traction unit Operator’s Manual for details on storing the machine. g019081 Figure 10 1. Compressor 2. Check the belt deflection here. 3. Increase or decrease the compressor-belt tension and tighten the bolts. 4. Check the deflection of the belt again to ensure that the tension is correct. -
Page 11: Schematics
Schematics g0 1840 1... - Page 12 Radial blower Expansion valve Evaporator (combined with heat exchanger for heating) Condenser—water Compressor Condenser Axial fans Dryer/filter Sight glass Drain Functional schematic of the air-conditioning system (Rev. -)
- Page 13 g019147...
- Page 14 Heating valve Compressor with magnetic clutch Twin axial fans Temperature sensor Electronic regulator Radial blower fan Blower-speed switch Pressure switch Main fuse in engine compartment Relay Electrical schematic of the air-conditioning system (Rev. -)
- Page 15 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.