Related Manuals for Blitz BZX3
Summary of Contents for Blitz BZX3
- Page 1 u s e r ’ s m a n u a l B Z X - 3 3 - W a y E l e c t r o n i c C r o s s o v e r N e t w o r k w / R e m o t e S u b w o o f e r L e v e l C o n t r o l...
- Page 2 I N T R O D U C T I O N . . . Thank you for purchasing the Blitz High performance Electronic Crossover. Rest assured you have purchased a quality product designed and engineered to give you many years un-compromised musical service.
-
Page 3: Table Of Contents
t a b l e o f c o n t e n t s general features precautions features and specifications system wiring mounting and installation noise check and system adjustment troubleshooting... -
Page 4: General Features
g e n e r a l f e a t u r e s 3-Way Electronic Crossover Chrome Plated Chassis Clear Acrylic Protective Cover Hi-pass Crossover: 32Hz - 800Hz for Front and Rear Channels X10 Frequency Multiplier for Front Channel Low-pass Crossover: 50Hz -160Hz for Subwoofer Channel 18dB Per Octave Crossover Slopes Variable Bass Frequency: 40Hz-120Hz... -
Page 5: Precautions
P r e c a u t i o n s To prevent short circuits, be sure to disconnect the negative battery ground lead before wiring the system up. When you finish the installation, be sure to make one more check to be sure everything is done correctly. Reinstate all car parts that were removed. - Page 6 P r e c a u t i o n s Primary Wiring Descriptions ELECTRICAL PRIME CONNECTION BATTERY + GROUND GROUND - REMOTE REMOTE B + CROSSOVER PRIME CONNECTION INPUT/OUTPUT FRONT RADIO/TAPE INPUT PLAYER TO CROSSOVER MODULE REAR INPUT RADIO/TAPE PLAYER TO CROSSOVER MODULE DUAL...
-
Page 7: Features And Specifications
f e a t u r e s a n d s p e c i f i c a t i o n s... - Page 8 1 Power Input Terminal (12V) To be connected to the positive terminal of your vehicle battery or other constant +12V source. 2 Ground Input Terminal To be wired to the vehicle's chassis ground 3 Remote Turn-on Input Terminal To be connected to the remote control wire or antenna lead of the source unit for remote (Remote) ON/OFF.
- Page 9 12 Subwoofer Frequency Selector For selection of the low-pass crossover frequency for the subwoofer channel between 50 Hz and 160 Hz. 13 Bass-Boost Frequency Control For setting the frequency (from 40 Hz to 120 Hz) at which the BASS-BOOST circuitry generates frequency boost to equalizer the woofer enclosure.
-
Page 10: System Wiring
S y s t e m w i r i n g A ) 2 - C H A N N E L T w o - W a y S y s t e m ( B ) 2 - C H A N N E L T w o - W a y S y s t e m ( T w e e t e r + f u l l r a n g e ) ( T w e e t e r + w o o f e r ) ( C ) 4 - C H A N N E L T R I - A M P S y s t e m... - Page 11 S y s t e m w i r i n g ( D ) 2 - C H A N N E L M u l t i p l e P u r p o s e S y s t e m...
-
Page 12: Mounting And Installation
M o u n t i n g a n d i n s t a l l a t i o n... -
Page 13: Noise Check And System Adjustment
NOISE CHECK Check the entire audio system for noise before permanently securing the CROSSOVER mounting 1. Start the engine. 2. Turn the audio system on. 3. Rev the engine and vary the VOLUME of the audio system to determine if there is any unwanted noise. If so, turn both the audio system and the engine off. -
Page 14: T B O U B L E S H O O T I N G G U I D E
T B O U B L E S H O O T I N G G U I D E PROBLEM 1. There is an audible distortion at a low volume level. Output levels NOT set correctly. 2. A whining sound can be heard through the speakers when the audio system is at low volume with the engine running. - Page 16 Should the product fail due to factory defects in material or workmanship, your unit will be repaired or replaced at the sole discretion of Blitz. To obtain warranty service you must first call our Consumer Return Hotline number at (718) 236-6948 to obtain a Return Authorization number.
Need help?
Do you have a question about the BZX3 and is the answer not in the manual?
Questions and answers