Table of Contents
Related Manuals for Faria Fuel Manager
Summary of Contents for Faria Fuel Manager
- Page 1 FUEL MANAGER FLOW TOTAL Fuel Management System Owner’s Manual • Display Fuel Flow in GPH or LPH • Total or trip Fuel Used • Low Fuel Alarm • Calculates Fuel Remaining In Tank • Gas Engines Only IS0324 rev A2 ecr 8451 03/2011...
- Page 2 Page intensionaly left blank Issue Date Description 1/26/11 Rev A ecr 8415 01/2011 2/08/11 A1 ecr 8415 02/2011 3/11/11 Rev A2 ecr 8451 03/2011...
-
Page 3: Table Of Contents
Contents Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . -
Page 4: Specifications
Specifications - for use with gas engines only. Size Fuel Remaining Mount 2 " diameter hole User enters a fuel value into memory. Depth behind face plate 3" min. The quantity of fuel used is Display 3-character LCD automatically subtracted from the total. This value remains in memory at power Backlighting down. -
Page 5: Installation
IMPORTANT Always install the Fuel Flow Transducer AFTER the primary lter. The primary lter must be a good quality water separator type with a minimum ltration of 30 microns or better. (10 or 2 micron. The lower the micron rating the ner the ltration) Failure to provide this level of ltration protection will result in inaccurate readings or total failure or damage to the transducer. -
Page 6: Wiring Connection
Wiring Connection Connect the red wire from the gauge to Keep electrical and transducer cables the positive supply through a 1 amp fuse away from alternator or other noise or a 1 amp circuit breaker . Connect the generating electrical cables. Avoid green wire from the gauge to the connecting the instrument to power electrical ground. -
Page 7: Instrument Setup
Instrument Setup Select units of measure display fuel values in US gallons, Liters or Imperial gallons. To change the current display setting, perform the following steps. 1. Power up the unit while holding key. 1. Reset the total log value to zero(see pg 9) 2. -
Page 8: Flow Averaging
Flow Averaging Flow Average Menu The Flow Averaging function sets the Follow the steps outlined below to enter averaged. The time period can be set in the Flow Averaging Menu: the range of 1 to 99 seconds. Normally, engines do not draw fuel from the tank Press and hold the key while at a constant rate. -
Page 9: Fuel Flow
Operation Change Fuel Remaining Fuel Flow change the value of fuel remaining Press the key to display the current in the tank press the key until displayed Press and hold both keys for 2 seconds Fuel Remaining Functions Press the key to cycle through the possible functions. -
Page 10: Changing The Fuel Remaining Value
Set Low Fuel Alarm Press any key to mute the alarm. The alarm text c To set the Low Fuel alarm, press both keys. as long as the alarm condition remains. Reset TRIP LOGs until ALRM is displayed To reset a log, press both the keys. until the display indicates the name of the log to be reset. -
Page 11: Troubleshooting Chart
Troubleshooting Chart No display 1 Check the DC power connections and DC polarity with the voltmeter. 2 Check fuse No flow reading indicated 1 Check connection to the flow transducer. 2 Remove the transducer from the fuel line, and perform a no pressure flush with the residual fuel left in transducer by covering the sensor inlet and outlet and shaking for 20 to 30 seconds. - Page 12 Copyright 2005 by the Thomas G. Faria Corporation, Uncasville CT Faria® is the trademark of the Thomas G. Faria Corporation. All rights reserved. No part of this publication may by reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission...
Need help?
Do you have a question about the Fuel Manager and is the answer not in the manual?
Questions and answers