Advertisement
alFra tma 600a
VarIaBler schweIßwInKel
de
adJustaBle weldIng angle
eN
angle aJustaBle de soudage
FR
eS
ángulo de soldadura VarIaBle
JusterBar sVeIseVInKel
NO
US Patent Nr. 8350663B1
BedIenungsanleItung
oPeratIon manual | mode d'emPloI | MANUAL DE INSTRUCCIONES | BRUKSANVISNING
alFra tma 600a #41100.A
alFra tma 600a #41100.A
Advertisement
Table of Contents
Related Manuals for ALFRA TMA 600A
Summary of Contents for ALFRA TMA 600A
- Page 1 600a VarIaBler schweIßwInKel adJustaBle weldIng angle angle aJustaBle de soudage ángulo de soldadura VarIaBle JusterBar sVeIseVInKel alFra tma 600a #41100.A alFra tma 600a #41100.A US Patent Nr. 8350663B1 BedIenungsanleItung oPeratIon manual | mode d‘emPloI | MANUAL DE INSTRUCCIONES | BRUKSANVISNING...
- Page 2 Thank you for purchasing an ALFRA product. Please read these operation instructions closely before using your device for the first time and keep them along with the enclosed Product Control Card for later reference. saFety InstructIons Danger can occur when using extremely strong magnetic clamps due to improper handling and/or poor maintenance, which may cause serious accidents with fatal physical injuries.
- Page 3 ProPer use The adjustable welding angle with TMC 300 magnetic clamp is a unit equipped with two switchable magnetic clamps, which is designed to position and to align different ferromagnetic, metallic work pieces to each other. It may only be used according to its technical data and determination. Proper use includes adherence to the start-up, operating, environment and maintenance conditions specified by the manufacturer.
- Page 4 technIcal data Prod.-No. 41100.a Designation Adjustable welding angle Breakaway force: per TMC >300 kg on 6 mm >660 lbs on 0.25" AISI CRS 1020 (at 0° inclination to the load) S235 Max. load-bearing capacity: 30% of the breakaway force 30% of the breakaway force (at 90°...
- Page 5 start-uP You have received a pre-assembled adjustable welding angle and a detailed operating manual. Please check the condition of the goods upon receipt for any damage incurred during transport, and make sure the delivery is complete. If you have any problems, please contactthemanufacturerimmediately. 1.
- Page 6 mountIng oPtIons (1) wIth clamPIng leVers and (2) wIth clamPIng screws maIntenance and InsPectIon oF the magnetIc clamP Regular maintenance and inspections are necessary to ensure the safe use of the switchable magnetic clamp. Furthermore, country-specific standards and regulations must be observed depending on application.
- Page 7 BasIc InFormatIon concernIng the handlIng oF magnetIc lIFtIng gear – In PartIcular tml / tmh / tmc The magnetic surface is located on the underside of the magnet incorporating multiple magnetic poles which generate the magnetic holding force when activated. The maximum holding force that can be achieved depends on different factors which are explained below: material thickness The magnetic flux of the permanent magnet requires a minimum material thickness to flow completely into the...
- Page 8 detaIled PerFormance data For the swItchaBle magnetIc clamP tmc 300 Values shown for the performance of the TMC 300 are based on measurements made on material S235 JR, comparable to AISI 1020 Cold Rolled Steel, for the maximum, vertical breakaway force at 0° deviation from the load axis and additionally under a 90°...
Need help?
Do you have a question about the TMA 600A and is the answer not in the manual?
Questions and answers