1. Manuals
  2. Brands
  3. Grote Manuals
  4. Kitchen Appliances
  5. 613-VS2-LES
  6. Equipment manual

Grote 613-VS2-LES Equipment Manual

Multipurpose slicer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Equipment Manual
Multipurpose Slicer
Model: 613-VS2-LES
Serial No: 1165423, consists of 1158300 slicer & 1176583 Auto Load Assy
PRECISION SLICING AND APPLICATION SYSTEMS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 613-VS2-LES and is the answer not in the manual?

Questions and answers

Related Manuals for Grote 613-VS2-LES

Summary of Contents for Grote 613-VS2-LES

  • Page 1 Equipment Manual Multipurpose Slicer Model: 613-VS2-LES Serial No: 1165423, consists of 1158300 slicer & 1176583 Auto Load Assy PRECISION SLICING AND APPLICATION SYSTEMS...
  • Page 3 J. E. GROTE COMPANY, Inc. CORPORATE HEADQUARTERS: 1160 Gahanna Parkway, Columbus, Ohio 43230 • Tel: 614-868-8414 • Fax: 614-863-1647 Parts and Service (Toll Free within USA): Tel: 1-888-53-GROTE (534-7683) • Fax: 1-888-39-GROTE (394-7683) E-Mail: service@grotecompany.com • sales@grotecompany.com EUROPEAN SALES/SERVICE: Wrexham Technology Park, Wrexham, North Wales LL137YP, United Kingdom Tel: Int +44 (0) 1978-362243 •...
  • Page 4 Copyright © 2016 J.E. Grote Company, Inc., All Rights Reserved. The information contained in this manual is covered by patents and trademarks of J. E. Grote Company, Inc. Grote and Accuband are registered trademarks of J. E. Grote Company, Inc.

  • Page 5: Table Of Contents

    R e j e c t C h u t e P r e s e n t S a f e t y S e n s o r S w i t c h ( C h u t e G u a r d ) ..3 0 “ Z e r o S p e e d ” S a f e t y S w i tch ............ 30 Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...
  • Page 6 1 2 . P r o d u c t n o t S t a c k i n g o r L a y i n g D o w n P r o p e r ly ....... 56 Grote Company...
  • Page 7 S h i p p e d W r o n g M e r c h a n d i s e ........... 59 D u p l i c a t e S h ipment ..............59 D R A W I N G S .................... 60 Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...
  • Page 8 Figure 1. Exit View of the Model 613-VS2 Multi-Slicer ..........3 Figure 2. Entrance View of the Model 613-VS2 Multi-Slicer .........4 Figure 3. 613-VS2-LES Top view with Tunnel Guard Closed........4 Figure 4: Top view with Tunnel Guard Opened ............5 Figure 5: Idle Side View with Autoloader attached ............5 Figure 6.

  • Page 9: Introduction

    Failure to follow safety warnings and instructions COULD result in death or serious injury. Failure to follow safety warnings and instructions could result in moderate injury. Failure to follow instructions could result in damage to your equipment. NOTE Pay particular attention to the information provided. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...
  • Page 10 • Adjustable product loading guides for feed alignment into slice chamber • Four swivel locking casters – detachable from slicing unit CONTROLS AND ELECTRICAL • Powered by slicing unit – no dedicated power source required • Stainless steel TENV AC gear motors Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 11: Setup

    M o d e l 6 1 3 - V S 2 - L E S , L o g E n d S l i c e r S e t u p SETUP The following figures show the various parts of the Model 613-VS2 Multi-Slicer and 613-VS2-LES. Refer to them and other detailed illustrations as you read the manual. Exit Closed...

  • Page 12: Figure 2. Entrance View Of The Model 613-Vs2 Multi-Slicer

    Drive Pulley Figure 2. Entrance View of the Model 613-VS2 Multi-Slicer Emergency Product Stop Button Guides Tunnel Guard Emergency Stop Button Emergency Stop Button Figure 3. 613-VS2-LES Top view with Tunnel Guard Closed Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 13: Figure 4: Top View With Tunnel Guard Opened

    Power & Communication plugs connecting the 613-VS2 & A t l Quick connect for air system Autoloader latching Figure 5: Idle Side View with Autoloader attached spool Safety Switch on Far side Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 14: Unpacking Procedure

    1. 6. Verify that the autoload system can be inserted into the 613-VS2. Variations in production floors may result in the need to adjust the equipment. Contact Grote Technical Services for advice. LOCATING AND POSITIONING THE SLICER The Multi-Slicer has casters for easy removal to a different location or cleaning station.

  • Page 15: Band Blade Installation

    4. Wrap the blade around one pulley at a time making sure the blade passes through the Blade Wiper and behind the lower blade guard. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 16: Figure 6. Blade Wiper

    8. The band blade must seat smoothly into Blade Guide slot. The Blade Guide is factory set to properly position the blade in its slot and seldom needs readjustment. However, when it does need adjustment, see Blade Guide Adjustment. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 17: Blade Tracking

    Use the procedure below to set drive side tracking. Drive Pulley Tracking Adjustment Screw Figure 8 Drive Side Tracking Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...
  • Page 18 8. Re-check idle side tracking. It may be necessary to go back and forth a few times between idle side and drive side tracking to ensure both sides track correctly. 9. Remove band blade and reinstall Blade Guide. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 19: Blade Guide Adjustment

    .02 or .03 inch. This increase may adversely affect slice quality, particularly with thinner slices, and the life of both the blade and Blade Guide. To decrease the clearance, manually adjust the X-Gap using the procedure below. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 20: Product Holders

    3/16” on the sides in the direction of blade travel. These guide lines are specific to the 613-VS2-LES. Standard product holders are three-part assemblies with inside and outside product holders and a product weight.

  • Page 21: Figure 11. Inside (Back) Product Holder Installed

    Failure to do so will result in the equipment being damaged! Weight Up Sensor (behind lift cylinder clevis) Inside Product Holder (Back) With Lift Cylinder Attached Low Product Sensor Figure 11. Inside (back) product holder installed Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 22: Detailed Product Holder Installation

    8. Upon installation of a new product holder, follow the dry stroke procedure to ensure proper product holder clearance throughout the stroke. Dry Stroke Procedure Follow this procedure to check product holder height clearance: 1. Set Lockout/Tagout switch to the closed (power off) setting. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 23: Product Holder Height Adjustment

    4. Adjust the height so that the product holder is level and 1/16 inch above the Blade Guide. 5. Tighten the Locking Bolts on both sides. 6. To check product holder height, perform the dry stroke procedure. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 24: Thickness Tray Adjustment

    10. Tighten all four Thickness Tray bolts. When Thickness Tray is assembled in lower slots, it may hit the shuttle and shuttle arms. For advice and additional information, contact Grote Service. Thickness Indicator Calibration (Optional) The Thickness Indicator displays a range of numbers between 3 and 98. These dimensionless numbers measure relative slice thickness.

  • Page 25: Figure 14. Thickness Proximity Sensor

    With the thickness set for minimum slice thickness, the sensor detects the highest portion of the cam. Loosen the nuts holding the sensor to the mounting bracket and adjust the sensor so that the thickness indicator reads 3. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 26: Autoload System

    Latching spool Figure 15. Autoloader detached Always insure there is ~5/8” to ~1/4”space between the cluster and the tip of the injection conveyor. Failure to do so will result in the equipment being damaged! Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 27: Reject Chute Installation And Removal

    Long belt on Wing Bolt outside Long belt on outside Individual Individual crown crown Two outer crowns Two outer (for short belts) not crowns not used on the feed conveyor Figure 16. Feed Belt Placement Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 28: Feed Belt Removal

    4. The Conveyor Belt has enough slack to then slide off the frame side rail. Installation and Direction of Travel Installation is opposite of removal. Ensure the belt spiral leads the crimped connector to which it is welded. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...
  • Page 29 M o d e l 6 1 3 - V S 2 - L E S , L o g E n d S l i c e r S e t u p Drive Direction Spiral Crimped Weld Connector Joint Figure 17. Carryout Conveyor, Correct Direction of Travel Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 30: Shuttle Conveyor System

    Shuttle Conveyor Bed at the desired slice thickness setting. The shuttle actuator arm should be removed from the thickness tray when it is either installed or removed from the slicer. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 31: Belt Replacement

    Figure 21. Shuttle Belt Loops NOTE The side pins are offset so the bed fits only one way. Side Side Figure 22 Shuttle Bed Installation Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 32: Static Sliter (Optional)

    Use care to align slots in the product holders with the blades or damage to the blades and product holders will occur. Damage to the machine will occur if the slice thickness range restrictions are exceeded. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 33: Noise Characteristics

    Test in outdoor open space. Background noise: 54-62 db. Noise meter set at a height of 1.3 meters. Test settings: C-Lo Scale, slow response. A: 78 dB B: 76 dB C: 80 dB D: 78 dB E: 80 dB F: 78 dB Figure 24. Top view with Sound Readings Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...
  • Page 34 M o d e l 6 1 3 - V S 2 - L E S , L o g E n d S l i c e r S e t u p Grote Company R-1176866 613-VS2-LES_CJL20160114.doc: 1/15/2016 4:21 PM...

  • Page 35: Operation

    When the Tray blade dulls (usually after eight hours of use), replace Thickness it with a new one. Grote offers various band blade Tray styles for optimized slicing of different types of products. A Blade Guide holds the band blade in place, and often, potable water lubricates the blade as it runs.

  • Page 36: Product Loading

    “0” and all voltage is removed from all components in the control enclosure. The indicator reads “1” when the switch is on. Padlock the switch in the off position to ensure safety for personnel performing electrical work or any other activity that requires lock out/tag out. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 37: Machine Enable Button

    This lock will not release until the blade has stopped and a key from the key switch has been inserted and turned. Power must be applied to the machine to release this lock. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/19/2016 10:55 AM...

  • Page 38: T U N N E L G U A R D L A T C H E D S A F E T Y S W I T C H ( T U N N E L G U A R

    Prior to and after adjusting the thickness, lock the thickness control shaft into position using the locking mechanism. Light tightening is sufficient to prevent the thickness from drifting. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 39: Figure 26. Thickness Control

    Thickness Control Thickness Lock Knob Control Adjustment Knob Air cylinder switches between standard thin slice and thick reject slice Note: that the Thickness control rod will move axially during operation Figure 26. Thickness Control Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 40: Operator Interface

    The basic description and functionality of your machine is described below. Your screens may vary due to the mechanical configuration of your machine. In addition, based on your specifications, functions (options) may be described that are not present on your machine. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 41: Main Screen

    DELAY, then indexes the conveyor at slow speed while it slices as many slices in a shingle as specified in the SLICE COUNT parameter. The sequence repeats. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...
  • Page 42 After the trim slices are complete, the conveyor will run in reverse for this many milliseconds, bringing the last draft back under the slice zone to complete the required number of slices for that draft. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 43: Status Scren

    The Status Screen displays existing alarms on the machine. Triggered alarms flash on the Status Screen. This screen also shows status of sensors on the machine as well as the phase of each major subsystem. Figure 31. HMI Status Screen Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 44: Sanitation

    S a n i t a t i o n SANITATION This section outlines basic guidelines for cleaning your Grote equipment. These guidelines are provided solely for the purpose of assisting the customer in developing an effective equipment Sanitation Standard Operating Procedure (SSOP). These safeguards will aid in protecting operators, maintenance workers and/or consumers of product processed by this equipment.
  • Page 45 Insure the inside cluster holder (cluster back) assembly is not fully submerged. This is to prevent the pneumatic cylinder from filling with water and sanitizer. b. The weight assembly may be removed from the lift cylinder clevis and soaked Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...
  • Page 46 S a n i t a t i o n NOTE NOTE: The Grote Company supplies a scraper tool to clean the Blade Guide slot. Use this tool with cleaner and sanitizer to thoroughly clean the Blade Guide slot. 15. The HMI screen should be gently wiped with soap and water and sanitizer. Gently rinse off all chemicals.

  • Page 47: Figure 32. Autoloader Being Washed

    27. Perform swab testing in accordance with your company Sanitation Operating Procedures. Areas of particular importance are in the product slicing zone consisting of the Band Blade, Blade Guide, Thickness Tray, Back Tray, Product Holders, Shuttle Tray, and Carryout Conveyor. Figure 32. Autoloader being washed Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 48: Figure 33. 613-Vs2 Ready For Sanitation

    M o d e l 6 1 3 - V S 2 - L E S , L o g E n d S l i c e r S a n i t a t i o n Figure 33. 613-VS2 ready for sanitation Figure 34. Items removed from the 613-VS2 for clean out of place Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 49: Guidelines For Sanitation Of Grote Blade Guides

    Following any chemical sanitizing, the blade guide must be thoroughly rinsed with clean water. Blade Guide Slot Cleaning Use a Grote slot scraper (part 1028659) to clean debris from the guide prior to sanitizing and recheck it afterward. The scraper is specifically designed for thorough penetration into the blade guide slot without damaging or prematurely wearing the guide.

  • Page 50: Maintenance

    Blade Guide to the other. If the scraper hits an obstruction, use care in dislodging it; the Blade Guide is hardened steel and subject to cracking. Consult a Grote Service Representative if the obstruction is not easily dislodged.

  • Page 51: Slot Width Checking Tool

    Monitor and adjust the chain tension as required and lubricate the gear unit, chain, sprockets, clutch shaft support bearings, and linkage joints as indicated in the periodic maintenance section. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 52: Tensioning The Drive Chain

    2. Loosen the Adjustable Keyless Bushing. Refer to section below. 3. Verify the Crank is in the home position by adjusting the Clutch so the Crank aligns with the Drive Link when in the stopped position. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...
  • Page 53 4. Manually adjust the Product Holder Frame so the Product Holder Back is .63 inches (16 mm) in front of the Blade Guide. Lock the Product Holder Frame in the position by tightening the Adjustable Keyless Bushing. Refer to section below. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 54: Adjustable Keyless Bushing Removal/Replacement

    5. Tighten screws gradually and evenly in ¼ turn increments, moving in a crossed sequence to an initial torque of 70 inch-pounds. 6. Tighten screws gradually and evenly in ¼ turn increments, moving in a crossed sequence to a final torque of 140 inch-pounds. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...
  • Page 55 Do Not Over Torque. 7. Starting from the last tightened screw, check that all screws are tightened to the final torque value in a clockwise continuous sequence. Do Not repeat the step above more than twice. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 56: Idle Side Pulley Bearing And/Or Pulley Replacement

    6. Remove bearing spacer and the other tapered roller from shaft. 7. Pull rear cap from shaft. Remove shaft seal and O-ring from rear cap and discard. 8. Press bearing outer race from pulley. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 57: Installing New Bearing

    To access the motor, remove the rear cover and side plate. Square Key Shaft Seal Drive Pulley Blade Pulley Pulley Mount Plate Clamping Cap Spacer Face Seal O-Ring Figure 40 Drive Side Pulley Assembly Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 58: Installing New Drive Motor

    9. Replace the front cap on the pulley with the four cap screws. 10. Reconnect the electrical cable to the motor. After the motor and pulley are installed on the slicer adjust the band blade tracking. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 59: Clutch Coil Maintenance

    Remove the two screws holding the actuator coil in place and unplug the two wires from the coil. Remove the old coil and install the new one. After installation, see Clutch Coil Adjustment to adjust the coil. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 60: Clutch Collar Adjustment

    2. Slide stop collar off the splines; rotate to desired stop position, and slide back on splines. Hold the actuator pawl clear during this operation. 3. Slide retaining ring back into groove. Do NOT disengage brake sleeve. It will damage the clutch. Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...
  • Page 61 M o d e l 6 1 3 - V S 2 - L E S , L o g E n d S l i c e r M a i n t e n a n c e Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 62: Troubleshooting

    • No Power to Speed Pack – Check power. • Faulty Motor – To check motor, supply power directly to the motor, instead of through the Speed Pack (motor should run at full speed only). Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 63: 7. Breaking Blades

    Verify product temperature is within the proper range for slicing. • Improper or Worn Blade Guide – Check for wear with Blade Guide tools. Use the correct style blade guide for your slicing application. Contact Grote Service. 10. PRODUCT SLINGING •...

  • Page 64: 1 . P R O D U C T N O T S L I C I N G O R S K I Pping

    • Not Enough Water - Check water pump for proper operation and output. • Blade Dull or Inside Out - Replace blade. Check blade for proper bevel installation. • Wrong Style Blade - Use the proper style blade for your slicing application. Contact Grote Service. 15. PRODUCT FRACTURING •...

  • Page 65: 6 . P R O D U C T Tailing

    • Product holder not centered • Product guides on aligned properly at the feed conveyor • Feed time too long will double load product – this may take several load cycles to show • Injection time too short Grote Company R-1176866 613-VS2-LES_CJL20160114.doc:1/15/2016 4:21 PM...

  • Page 66: Spare Parts List

    Inverter Parameters Mitsubishi D-700 Part No. : 1166893 Machine : 613--Cluster Inverter : 1 hp, 230 v, 1121618 Date : 9/13/12 Engineer : MAK Parameter Parameter Units Range Factory Machine Torque Boost (manual) 0 to 30 Upper limit frequency 0 to 120 0.01 60 * Lower limit frequency...
  • Page 67 Inverter Parameters Mitsubishi D-700 Pr 79 Operation mode 1 keypad only enabled 2 external operation only 3 freq set via keypad, run via external signal 4 freq set via external signal, run via keypad To set parameters press PU/EXT button until PU indicator light is on press MODE button until display reads P 0 turn dial until the desired parameter number is displayed press SET button to access parameter value...
  • Page 68 Inverter Parameters Mitsubishi D-700 Part No. : 1174601 Machine : 613-VS2 Conveyor Inverter : 1 hp, 230 v, 1121618 Date : 3/31/14 Engineer : MAK Parameter Parameter Units Range Factory Machine Torque Boost (manual) 0 to 30 Upper limit frequency 0 to 120 0.01 80 *...
  • Page 69 Inverter Parameters Mitsubishi D-700 To reach parameter C2: Press mode until P 0 appears. Rotate dial until C . . appears, press set. Rotate dial until C 2 appears, press set. Change setting to desired value, press set. Rotate dial until C - appears, press set. Rotate dial to change final parameter, P 79.
  • Page 70 Inverter Parameters Mitsubishi D-700 Part No. : 1174605 Machine : 613-VS2 BLADE Inverter : 2 hp, 230 v, 1127982 Date : 4/21/14 Engineer : MAK Parameter Parameter Units Range Factory Machine Torque Boost (manual) 0 to 30 Upper limit frequency 0 to 120 0.01 60 *...
  • Page 71 Inverter Parameters Mitsubishi D-700 To reach parameter C2: Press mode until P 0 appears. Rotate dial until C . . appears, press set. Rotate dial until C 2 appears, press set. Change setting to desired value, press set. Rotate dial until C - appears, press set. Rotate dial to change final parameter, P 79.
  • Page 72 Inverter Parameters Mitsubishi D-700 Part No. : 1174829 Machine : Auto Load, Feed Inverter : 1 hp, 230 v, 1121618 Date : 4/15/14 Engineer : JRD Parameter Parameter Units Range Factory Machine Torque Boost (manual) 0 to 30 Upper limit frequency 0 to 120 0.01 90 *...
  • Page 73 Inverter Parameters Mitsubishi D-700 Pr 79 Operation mode 1 keypad only enabled 2 external operation only 3 freq set via keypad, run via external signal 4 freq set via external signal, run via keypad To set parameters press PU/EXT button until PU indicator light is on press MODE button until display reads P 0 turn dial until the desired parameter number is displayed press SET button to access parameter value...
  • Page 74 Inverter Parameters Mitsubishi D-700 Part No. : 1174830 Machine : Auto Load, Inject Inverter : 1 hp, 230 v, 1121618 Date : 4/15/14 Engineer : JRD Parameter Parameter Units Range Factory Machine Torque Boost (manual) 0 to 30 Upper limit frequency 0 to 120 0.01 90 *...
  • Page 75 Inverter Parameters Mitsubishi D-700 Pr 79 Operation mode 1 keypad only enabled 2 external operation only 3 freq set via keypad, run via external signal 4 freq set via external signal, run via keypad To set parameters press PU/EXT button until PU indicator light is on press MODE button until display reads P 0 turn dial until the desired parameter number is displayed press SET button to access parameter value...

  • Page 76: Grote Part Return Policy

    Authorization number on the outside of the box. After Grote receives and inspects the items, we determine credit. NOTE: The customer is responsible for the cost to ship the item(s) to Grote. Credit will not include freight. Reasons for Return Defective A description of the defect is required.

  • Page 77: Repair/Rebuild

    Return items in the original package. Grote issues credit upon return. Correct items ship upon notification of the mistake. Duplicate Shipment Return items in the original package. Grote issues credit upon return if we can return the parts to stock and there is no damage. PARTS AND SERVICE J.
  • Page 78 V1083779 1087329 CABLE, QD, M12, 5M, R/A, 4 PIN 1087624 RELAY, SPDT, 24 VDC, ULTRA-SLIM 1087800 BEARING CAP, REAR IDLE PULLEY B1087800 1096807 PUMP, MINI-BELLOWS, 1/2" 24VDC V1096807 LGRV COLS GROTE COMPANY Page 1 of 3 bsapp 3/27/2017 2:08:30 PM...
  • Page 79 TUBING, YELLW, 8MM OD, POLYURETHANE 1160642 VALVE, PNEU, 5/2, R1/4, 1 SOL, BDY P 1161044 BEARING, SS, 20 MM ID, 3 BLT FLG 1162005 KNOB, SS, M8 X 16MM, WING SCREW COLS GROTE COMPANY Page 2 of 3 bsapp 3/27/2017 2:08:30 PM...
  • Page 80 FTG, AIR, FLC, R1/4, T8, P, ELBOW 6800-0052-01 FTG, AIR, FLC, R1/4, T6, P, ELBOW 6800-0097-01 FTG, AIR, QRC, GF1/4, S, SR23 PLUG 6800-0104-01 FTG, AIR, STR, G1/4, T8, N COLS GROTE COMPANY Page 3 of 3 bsapp 3/27/2017 2:08:30 PM...

  • Page 81: Drawings

    D r a w i n g s DRAWINGS The following pages contain drawings for the major assemblies and an electrical schematic comprising the Multi-Slicer. Parts illustrated in the assemblies are identified with Grote Part Numbers listed on the following page. Grote Company...
  • Page 82 1085587 HEX SCR METRIC M6-1 X 25mm 1085492 EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01 WHOLE OR IN PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF THE J.E.
  • Page 83 DETAIL C DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: SCALE 1 : 2 NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 84 DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE:...
  • Page 85 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 86 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 87 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 88 DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE:...
  • Page 89 DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE:...
  • Page 90 1149477 THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE:...
  • Page 91 THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE DEFAULT TOLERANCES ARE: DEFAULT TOLERANCES ARE: EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN...
  • Page 92 DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE:...
  • Page 93 THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE TIGHTEN SCREWS GRADUALLY AND EVENLY IN 1/4 TURN INCREMENTS, EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE:...
  • Page 94 BELT PATH DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01 WHOLE OR IN PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF THE J.E.
  • Page 95 THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE DEFAULT TOLERANCES ARE: DEFAULT TOLERANCES ARE: EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN...
  • Page 96 DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE:...
  • Page 97 THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE DEFAULT TOLERANCES ARE: DEFAULT TOLERANCES ARE: EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN...
  • Page 98 THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE HEX NUT METRIC M4 - .7 1114814 EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01 WHOLE OR IN PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF THE J.E.
  • Page 99 THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE DEFAULT TOLERANCES ARE: DEFAULT TOLERANCES ARE: EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN...
  • Page 100 DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE DEFAULT TOLERANCES ARE: EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01 WHOLE OR IN PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF THE J.E.
  • Page 101 1165784 DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN FEED BELT ASY, MODULAR BELT, 613-LES 1165780 .XX = .01...
  • Page 102 1035292 DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE M25 X 1.5, .485 - EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: CORD GRIP 1140650 NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .709...
  • Page 103 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 104 1138901 DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN LATCH POSITIONER, FAB 1165491 .XX = .01...
  • Page 105 THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE SWITCH, SAFETY, INTERLOCK, 24VAC/DC 1070635 EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 106 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 107 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 108 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 109 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 110 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 111 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 112 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 113 THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE DEFAULT TOLERANCES ARE: EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN WHOLE OR IN PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF .XX = .01...
  • Page 114 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 115 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 116 J.E. GROTE COMPANY, INC. DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...
  • Page 117 THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE DEFAULT TOLERANCES ARE: EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN WHOLE OR IN PART WITHOUT THE EXPRESS WRITTEN PERMISSION OF .XX = .01...
  • Page 118 1160615 1160358 1160622 DIMENSIONS ARE IN INCHES. THIS DRAWING CONTAINS CONFIDENTIAL INFORMATION AND IS THE EXCLUSIVE PROPERTY OF THE J.E. GROTE CO. NEITHER THE DOCUMENT, DEFAULT TOLERANCES ARE: 1159070 1160357 1160620 NOR ITS CONTENTS, ARE TO BE USED, REPRODUCED OR DISCLOSED IN .XX = .01...

This manual is also suitable for:

1165423

Table of Contents

Save PDF