1. Manuals
  2. Brands
  3. Acmeda Manuals
  4. Engine
  5. Automate RF 500 Series
  6. Programming instructions manual

Acmeda Automate RF 500 Series Programming Instructions Manual

Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

AUTOMATE EL MOTORS / PROGRAMMING INSTRUCTIONS
These instructions show how to install, program and use Acmeda's electronic limit tubular motors:
•
Automate EL S45
•
Automate Q EL S45 (quiet motor)
•
Automate EL S60 (with collision control technology)
•
Automate EL A50 (for open awnings)
•
Automate EL A50/C (for cassette awnings)
•
Automate C EL (Curtain motor)
These motors can be controlled with Automate RF 500 series remote devices:
•
Automate RF501 (single channel)
•
Automate RF515 (15 channel)
•
Automate RF505 (5 channel timer)
CE
433MHz
All controls support 433MHz
All controls support 230V/50Hz
Electronic
Electronic Limit + Built-in Receiver
CIRCUIT INSTALLATION
RF5
RF500 series Remote Control
1
2
AC
3
Only use
Acmeda tail
FEB 2014
Electronic Limit Tubular Motor

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Automate RF 500 Series and is the answer not in the manual?

Questions and answers

Scott
July 31, 2025

1 and 4 are flashing and will not work on auto can you please help

0

Related Manuals for Acmeda Automate RF 500 Series

Summary of Contents for Acmeda Automate RF 500 Series

  • Page 1 AUTOMATE EL MOTORS / PROGRAMMING INSTRUCTIONS FEB 2014 These instructions show how to install, program and use Acmeda’s electronic limit tubular motors: • Automate EL S45 • Automate Q EL S45 (quiet motor) • Automate EL S60 (with collision control technology) •...

  • Page 2: Motor Position

    P R O G R A M M I N G A M O T O R I N 5 S I M P L E S T E P S R E M O T E O V E R V I E W FRONT BACK LCD Screen...
  • Page 3 STEP 3 PUT MOTOR IN LIMIT SETTING MODE a. Press P2 bu on (x1). b. Press UP bu on (x1). c. Press P2 bu on (x1). P2 (x1) P2 (x1) UP (x1) UP (x1) P2 (x1) P2 (x1) To confi rm se ng mode, motor will beep 3 mes and jolt up and down. STEP 4 SET UPPER LIMIT FIRST *To program an A50/C Motor go to Step 5...
  • Page 4 P R O G R A M M I N G W I T H A M U L T I C H A N N E L R E M O T E A mul channel remote allows you to control several blinds or groups of blinds on one device. Each channel can be programmed like a single channel remote, by following the below instruc ons.

  • Page 5: Return To Factory Settings

    C A N C E L L I N G L I M I T S A N D R E M O T E S To modify limits you need to cancel all limits previously applied, by following the below instruc ons. CANCEL LIMITS FROM MOTOR a.

  • Page 6: Set The Clock

    F I V E C H A N N E L T I M E R R E M O T E P R O G R A M M I N G The RF 505 Remote can ac vate the motor twice a day (Opening Time and Closing Time), each day of the week, at the me set during programming.

  • Page 7: Timer Programming

    TIMER PROGRAMMING • TI M E D IF FE RE NC E B ET WEEN OPENI NG AND C LOS IN G MUST BE MORE THAN 32 MIN UT ES . STEP 1 ENTER PROGRAMMING MODE Switch to AUTO mode pressing Mode bu on. Select a channel (i.e Channel 1) Press mer bu on for 3 seconds.
  • Page 8 A U T O M A T E C - C U R T A I N M O T O R P R O G R A M M I N G se ng bu on external swith interface LED light STEP 1 PAIR MOTOR WITH REMOTE...

This manual is also suitable for:

Automate rf501Automate rf515Automate rf505Automate el s45Automate q el s45Automate el s60 ... Show all

Table of Contents