6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Disassembly/Assembly Nokia Customer Care Disassembly Instructions Use the following steps to disassemble the phone. 1. Remove the Battery Cover (B-cover) A. Turn the phone off. B. Push down on the release button, and slide the B-cover away from the phone.
6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Nokia Customer Care Disassembly/Assembly 2. Remove the A-cover While squeezing the sides of the D-cover at the snap locations, separate the bottom of the A-cover from the D-cover. D-cover Snaps A-cover 3. Remove the Screws The D-cover screw bosses do not have threads; the threads are created using self- threading screws at the factory when the phone is assembled the first time.
6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Disassembly/Assembly Nokia Customer Care 4. Remove the LCD Assembly Unhook the D-cover snap on one side to free the LCD assembly from the D-cover. Repeat on the other side and remove the LCD assembly. Unhook D-cover snaps (both sides) 5.
6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Nokia Customer Care Disassembly/Assembly 6. Remove the Power Button 7. Remove the PIFA Antenna Grasp the PIFA antenna and pull up to remove it from the D-cover. Avoid touching the electrical contacts. Electrical contacts 8. Remove the Headset Jack from the PIFA Antenna Unhook the two clasps on either side and grip the jack with tweezers to remove it.
6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Disassembly/Assembly Nokia Customer Care 9. Remove the Whip Antenna Grip the protruding end of the whip antenna and carefully pull it out of the top of the D-cover. Whip assembly 10. Removing the DC Jack, Vibra Motor, and Microphone 1.
6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Nokia Customer Care Disassembly/Assembly 11. Disassembling the LCD Module A). Disconnect the first two BB spacer snaps. Apply force to the inside of the BB spacer behind the snap. Push towards the outside and then towards the top.
6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Nokia Customer Care Disassembly/Assembly Assembly Instructions Use the following steps to assemble the phone. 1. Assemble the Whip Antenna Slide the whip antenna into the hole at the top of the D-cover. Ensure that the key is lined up and the antenna is fully inserted into the D-cover (you will feel a small click).
6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Disassembly/Assembly Nokia Customer Care 3. Assemble the DC Jack Use tweezers to grip the sides of the DC jack and place it in the D-cover. Do not touch the connectors on the top of the jack. Push down on the back of the jack to ensure that it is securely in place.
6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Nokia Customer Care Disassembly/Assembly 6. Assemble the Headset Jack Use tweezers to grip the headset jack above the snap tabs and place the jack in the D-cover. Do not touch the connectors on the top of the jack. Carefully push down between the connectors and ensure that the tabs lock into the PIFA antenna snaps.
6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Disassembly/Assembly Nokia Customer Care 8. Assemble the PWB A). Use the upper guide pin to align the top of the PWB with the D-cover. Upper guide pin B). Use the lower guide pin to attach the PWB to the D-cover assembly.
6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Nokia Customer Care Disassembly/Assembly 9. Assemble the LCD Display Without touching the display, attach the LCD display assembly by aligning the lightguide pins with the D-cover snaps on both sides. Do not press on the LCD display...
6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Disassembly/Assembly Nokia Customer Care Carefully tighten the two middle screws before tightening the top and bottom sets. 11. Assemble the Type Label Insert the type label in the battery compartment of the D-cover as shown below.
6015/6015i/6016i/6019i (RH-55), 6012 (RM-20) Nokia Customer Care Disassembly/Assembly 12. Assemble the A-Cover Snap the A-cover to the phone assembly by aligning the snaps and hooks on both sides and the top of the assembly. 13. Assemble the B-Cover Align the B-cover with the slots on the back of the phone assembly, push down, and slide the B-cover into place.