Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Buffalo 320
- Page 1 DRYWALL STILTS Important Please Read This Manual Before Assembly or...
- Page 2 ATTENTION! READ THIS! PLEASE ENSURE ASSEMBLY, INSPECTION AND MAINTENANCE IS CARRIED OUT PROPERLY. THIS IS CRUCIAL TO YOUR PRODUCT SATISFACTION AND PERSONAL SAFETY. IT IS YOUR RESPONSIBILITY TO READ THESE INSTRUCTIONS INCLUDING THE DO’S AND DON’TS GUIDELINES DETAILED WITHIN. IT IS ALSO YOUR RESPONSIBILITY TO USE STILTS THAT ARE WELL MAINTAINED, TO INSIST ON A CLEAN, CLEAR WORK AREA, AND TO ALWAYS EXERCISE CAUTION WHILE USING SUPA-...
- Page 3 DO… • Inspect stilts thoroughly before use, making sure that construction is free from damage and hazards, that there is no excessive wear at the connection points, and that all bolts are tight. Special attention should be given to the entire strut tube assemblies and wing bolts in this respect.
- Page 4 DO NOT… • Wear stilts without having the proper instruction. • Wear stilts that are uncomfortable or not adjusted properly. • Wear stilts without having first inspected them for obvious hazards. • Wear stilts that have clearly been misused damaged or modified.
- Page 5 ASSEMBLY INSTRUCTIONS Strut Tubes 1. Loosen tube clamps. Insert lower strut tubes up through the bottom of the tube clamps. Leave tube clamps whilst you prepare the other parts. 2. Attach lower strut tubes to the safety-lock bracket with the attached 1/4 x 1 1/2"...
- Page 6 Strap Kit 1. Position the toe (short) and arch (long) straps on the footplates with the fasteners on the same side as the strut tube. 2. Feed the ends of both straps over and through the Safety Anchor Slot System and secure the straps with the strap plate & screws provided.
-
Page 7: Height Adjustment
Height Adjustment When adjusting the heights of the stilts remove wing bolts. Once removed evenly raise the stilt legs to the desired height. Once height is achieved re-align the wing bolt holes in legs and extension tubes replace the bolts and tighten well. Be sure not to over tighten as this can have adverse effect. - Page 8 MAINTAINANCE Lubrication In order to keep your stilts operating freely, it is necessary to keep the components reasonably clean and free of dents or burrs. Pay special attention to the components which help operate the movement. Lubricate these moving components lightly with a silicone spray or white graphite powder.
- Page 9 OPERATION GUIDELINES Walking precautions IMPORTANT Always take short, deliberate, distinct steps and walk with your stilts well apart. Large or over-extended steps can cause the action springs to bottom out and place excess stresses on the stilt components. Excess stresses could drastically reduce the life of the stilts or result in component breakage.
-
Page 10: Learning To Walk
LEARNING TO WALK IMPORTANT Read the do's and don'ts for the use of your stilts before you attempt to learn to walk on them. Remember, in order to develop safe work habits, it is very important that you observe the do's and don'ts as you learn to walk on and work with them. -
Page 11: Parts Diagram
PARTS DIAGRAM... -
Page 12: Parts List
Parts List Part No. Description Qty. Leg band with pads Leg band spacer 1/4"-20*2"flat bead machine screw with locknut Adjustable double hook & loop fastening leg strap PR5-15 1/8"upper strut tube(PW1523) PR5-18 1/8"upper strut tube(PW1830) PR5-24 1/8"upper strut tube(PW2440) No,10,24*1/2" machine screw with nut PR6A Locknut Loop fastening arch strap... - Page 13 PR29 Side pole cap clamp PR30 Side pole support clamp PR31 3mm clamp bracket PR32 ¼”- 20x1 ¾” cap screw PR33 Upper side pole cap plug PR35 Strap mounting screw PR37 Sole mounting screw PR42 Wing bolt PR44 Lower coil spring PR45 Entire spring construction PR46...
-
Page 14: Repair Kit
Repair Kit RS6001 Item # Content PR11 leg bearing PR 12 1/4" flat washer PR 13 1/4" - 20 locknut PR 27 1/4" - 20 x 3" cap screw RS6002 Item # Content PR 35 strap mounting screw PR 17 strap mounting washer PR 4 adjustable double hook &...