Advertisement
Quick Links
Arc Enclosure
Instruction Manual
Consumer Guarantee -
Important: If you are fitting this product with integrated water delivery, the valve must be installed before
tiling the showering area and before the installation of this product.
which is enclosed with this product. Failure to validate the Guarantee will mean only the 1 Year Statutory Guarantee will apply.
FA - Freedom Arc Dec 2009:CQB
1. Check you have the correct enclosure and tray. Please look at the labels on the side of the product packaging.
2. Check all the product components are in the box and the fixing kits are complete. Please check this with the component
check list overleaf.
3. Unpack your product and handle it with care.
4. Please check the product for defects or damage. Once the installation has commenced we cannot accept responsibility for
any defects or damage to the products.
5. Please take the time to read these instructions prior to installing your product.
6. Before you commence any drilling check there are no hidden electrical cables and/or water pipes in the walls.
7. No attempt should be made to re-work the toughened safety glass.
8. The installation should be performed by two persons.
9. It is strongly recommended the walls the product is going to be installed on are vertical. However the wall profiles have
25mm of adjustment to help compensate for some deviation.
10. It is strongly recommended the product is fitted on tiled surface or similar waterproof surface.
11. It is strongly recommended the walls are tiled and grouted after the installation of the tray and before the installation of the
product. This will provide maximum adjustment and help when sealing the product.
12. If the walls and/or the tray are not level you will not achieve maximum adjustment of the product.
13. Pictures used are for illustration purposes only, product designs may alter slightly as a result of continuing product
development.
14. We do not stipulate where the European Standard Kite Mark should be positioned on the glass panels when being factory
assembled.
• Roman's toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are
installed according to our guidelines.
• It is important to note, that the glass must not be mounted or 'pinched' in such a way that would cause a stress point to
develop in the glass. In addition, it must not be subjected to any sharp impact or severe temperature fluctuation which may
also cause a stress point to develop in the glass.
• Roman's toughened glass is physically and thermally significantly stronger than standard glass. During our toughening
process the stresses contained within any glass are balanced so if in the unlikely situation any of the above occurs and the
glass breaks, the glass will shatter safely into small thumbnail sized blunt fragments.
IMPORTANT PRE-INSTALLATION CHECKS
Please make sure the purchaser/end user completes and returns the Guarantee card
4/5/10
12:05
Page 1
IMPORTANT INFORMATION
FA
FA/May 10
Advertisement
Summary of Contents for FA Arc Enclosure
- Page 1 Failure to validate the Guarantee will mean only the 1 Year Statutory Guarantee will apply. FA - Freedom Arc Dec 2009:CQB 4/5/10 12:05 Page 1 1.
- Page 2 Step 1 - Checking the tray 40 mm Screws Wall Plugs 16mm Pan Head Screws Branding Badge Profile Cover Caps 4mm Allen Key FA - Freedom Arc Dec 2009:CQB 4/5/10 12:05 Page 2 3mm Allen Key 3mm Drill Bit Plastic Tray Pin 1.
- Page 3 Step 2 - Fixing the Wall Profiles WALL PROFILE LIP FA - Freedom Arc Dec 2009:CQB 4/5/10 12:05 Page 3 1. Position the wall profiles using the guides on the tray, the lip of the profiles face towards the inside of the enclosure (look at point 2 above).
- Page 4 Step 3 - Fit the hinge panel. (Please ensure the transport bands are removed with care from the glass panels in this and the following steps. Make sure the vertical seals on the glass panels are carefully re-positioned). FA - Freedom Arc Dec 2009:CQB 4/5/10 12:05 Page 4 1.
- Page 5 Step 4 - Assembling the Brace Bars (If you are fitting with intergrated water delivery, please refer to your valve instructions for this step) FA - Freedom Arc Dec 2009:CQB 4/5/10 12:05 Page 5 ➂ ➃ 1. Assemble the straight section of the brace bar onto the Low Level brace assembly and fasten together with the countersunk screw: then slide the wall cup assembly onto the other end of the brace bar.
- Page 6 Step 5 - Fitting the door and seals FA - Freedom Arc Dec 2009:CQB 4/5/10 12:05 Page 6 ➀ ➆ ➃ 1. Assemble the handle onto the door. (There should be no metal toughing the glass. The spacers must be...
- Page 7 Step 6 - Fix the Cover Caps and Seal the enclosure. FA - Freedom Arc Dec 2009:CQB 4/5/10 12:05 Page 7 1. Clip on the wall profile cover trims. (They are designed to be a tight fit so take care).
- Page 8 Spare Parts: If you require any spare parts, please look at the parts list below then call customer services on 01325 328034 NB: If ordering item 18 please state Left or Right Hand. FA - Freedom Arc Dec 2009:CQB 4/5/10 12:05 Page 8 ITEM NO.
- Page 9 Straight to floor guidance FA - Freedom Arc Dec 2009:CQB 4/5/10 12:05 Page 9 Locating the wall profiles and using the panel location pins (steps 2, 3 and 5). The measurements above need to be used to locate the wall profiles (step 2).
- Page 10 10.Check the vertical door and panel magnet seal are locating along the full length (Step 5). ENCLOSURE 1. Check the wall profiles have been installed as per the instructions: ALIGNMENT 2. Make sure they are vertically level (Step 2). FA - Freedom Arc Dec 2009:CQB 4/5/10 12:05 Page 10 ON TRAY 3.