1. Manuals
  2. Brands
  3. Matrix Telecom Manuals
  4. Cell Phone
  5. VISION
  6. Quick start manual

Matrix Telecom VISION Quick Start Manual

The office communicator
Hide thumbs
Table of Contents

Advertisement

Quick Links

VISION
Quick Start

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VISION and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Matrix Telecom VISION

  • Page 1 VISION Quick Start...
  • Page 3 VISION The Office Communicator Quick Start...
  • Page 4 Documentation Disclaimer Matrix Comsec reserves the right to make changes in the design or components of the product as engineering and manufacturing may warrant. Specifications are subject to change without notice. This is a general documentation for all models of the product. The product may not support all the features and facilities described in the documentation.

  • Page 5: Table Of Contents

    Contents Know Your VISION ..................1 Overview ......................1 Installing VISION .................... 3 Before you Start ....................3 Installing VISION ....................4 Configuring VISION ..................7 How to Configure ....................7 Test Calls ......................13 Reinstate Default Settings ................13 Forgot Programming Password? ..............

  • Page 6: Know Your Vision

    This is a common Quick Start for all models. For the purpose of illustration, the model VISION 308S has been used. The Trunk ports of VISION are numbered as 0, 1 and 2. The software ports of the stations are numbered from 00-08 in VISION 309P .
  • Page 7 VISION 308S LED Indication Matrix VISION Quick Start...

  • Page 8: Installing Vision

    You will need Single Line Telephones (SLT) to be connected as stations. Any ordinary push button phone, with or without Call Line Display, even cordless phones can be connected to the VISION. Decide the number of stations you would like to connect and arrange for the SLTs.

  • Page 9: Installing Vision

    Use SLTs equipped with a Flash Key, as several features supported by VISION require you to use the the Flash Key. If your phone does not have a Flash Key, tap the Hook switch to dial Flash. Installing VISION Select a suitable place on the wall to mount VISION.
  • Page 10 Repeat the above steps to connect other Trunks and Stations. Connect a Computer. • Connect the COM Port of VISION to the COM Port of the Computer using the RS232C cable (9-pin, with D-type female connectors at both ends). On the Windows operating system use the Hyperterminal to generate the Configuration and the Station Message Detail Recording Reports.
  • Page 11 To access the Hyperterminal, on a Windows operating system, select StartAll Programs Accessories Communications Hyperterminal. Connect Other Interfaces. • VISION 309P provides other interfaces like Auto Attendant, Door Phone, Door Lock, External Music devices, Public Address System and the Security Dialer. To connect these interfaces, •...

  • Page 12: Configuring Vision

    Configuring VISION How to Configure VISION can be programmed by dialing commands or using the Phone Wizard provided for quick programming of basic features. Follow the instructions given below to configure the system using the Phone Wizard. Enter the Programming Mode from Station-21.
  • Page 13 Denied List (DL) = 0 to 7. • To set the same Toll Control on all stations, dial: 32-*-Day Allowed/Denied List-Night Allowed/Denied List Clear All Features • To clear all features on a station, dial: 343-Flexible Number of the Station Matrix VISION Quick Start...
  • Page 14 Disable = 0. Enable = 1. Direct Outward System Access (DOSA) • To Enable/Disable DOSA on a trunk, dial: 45-Trunk-Day Code-Night Code Where, Trunk = 0 to 2. Day Code / Night Code Disable = 0. Matrix VISION Quick Start...
  • Page 15 46-*-Day Hunting Scheme-Night Hunting Scheme Hunt Timer It is the time for which a station rings when a call lands on it. After expiry of the timer, the next station in the Station Group starts ringing. Matrix VISION Quick Start...
  • Page 16 Code not assigned No Trunk Code not assigned Trunk Access Access Code to be Dialed to Group Index access the Trunks in the Group Code not assigned Code not assigned Code not assigned Code not assigned Matrix VISION Quick Start...
  • Page 17 • To assign a Trunk Access Group and a Trunk Access Code to all stations for Day time, dial: 4411-*-Trunk Access Group Index-Trunk Access Group • To assign a Trunk Access Group and Trunk Access Code to a station for Night time, dial: 4412-1-Station-Trunk Access Group Index-Trunk Access Group-#* Matrix VISION Quick Start...

  • Page 18: Test Calls

    • Assign a Trunk Access Group and Trunk Access Code to all stations for Night time, dial: 4412-*-Trunk Access Group Index-Trunk Access Group Exit the SE Programming Mode. • Dial 00. Congratulations! Your VISION is now ready for call operations. Test Calls Making a call To make an external call: •...

  • Page 19: Forgot Programming Password

    • Wait for 15 seconds. Do not touch the device! • Switch off power supply, remove power cord. • Restore mini jumper to original position B-C. • Replace top cover. • Switch on power supply. • Default SE password is restored. Matrix VISION Quick Start...
  • Page 20 MATRIX COMSEC PVT. LTD. Corporate Office 394-GIDC, Makarpura, Vadodara - 390010, India. Tel.:+91 265 2630555, Fax: +91 265 2636598 E-mail: Info@MatrixComSec.com Factory 15 & 19-GIDC, Waghodia - 391760, Dist. Vadodara, India. Tel.: +91 2668 263172/73 Customer Care Tel.: +91 265 2630555 E-mail: Customer.Care@MatrixComSec.com, Support@MatrixComSec.com www.MatrixComSec.com...

This manual is also suitable for:

Vision 206sVision 308sVision 309p

Table of Contents