Magnetic KICK-OFF II Instruction Manual page 2

GB
Magnetic Kick Off II Electric Filing System
CHECK VOLTAGE!
READ INSTRUCTIONS BEFORE USE!
Application
The Kick Off II electric file is designed for all nail filing
techniques (for removing of old enhancements, buffing and
sculpting etc). Read – for your own benefit – the following
conditions regarding the instructions and warranty of your Kick
Off II Electric File. Keep the instructions near the electric file for
everyone to read who uses the machine.
Specifications
Model: Kick Off II
Wattage: 110/220 V CHECK VOLTAGE!
50/60 HZ DC 30V/0.5A
Dimensions: width 112 mm x depth 147 mm x height 78 mm
Weight: 1,25 kg
The specifications and designs in this instruction manual are
subject to change without notice.
Safety Precautions
• Please work safe and responsible. Knitted gloves, clothes
with open cuffs and long hair are likely to being caught in
the machine.
• Please wear goggles to prevent dust and particles from
getting in the eyes. In addition, please wear a disposable
mouth mask to prevent breathing in dust and particles.
• Please use the machine in a dry, ventilated space with
a temperature between 0 and 40 degrees Celsius with
an average humidity varying between 20 to 80% (no
condensation). Never use the machine in a wet or humid
place. Moisture can cause short circuiting, fire or rust.
• During operation, sparks of fire can occur in the hand
piece. Never use the machine near flammable or explosive
materials such as lacquer, paints, thinner, gasoline, gas,
adhesives et cetera.
• Please make sure cord and plug are not damaged to prevent
current leakage, shocks or fire. Always check cords and
cables before starting the machine. Let a broken cord be
repaired by a professional.
• Use the machine in a clean, tidy place to avoid tripping over
cords.
• Please use bits with specified standard for the machine.
Please work within the permitted range of rotation.
• Please do not place a cloth or anything else on the
ventilation slits of the machine. Also, please avoid using the
machine while any dust is attached around the ventilation
holes.
• Avoid contact with flammable materials like alcohol, oil and
other liquids.
• Please do not blow compressed air into ventilation holes of
the machine.
• Turn off the machine during absence.
• Keep the machine out of reach of children.
• Never operate the machine without a bit.
• When operating an electric file, we urgently advice you to
use a built-in table vent.
• Never change anything to the machine that could affect the
original functionality or safety.
• Never use the machine for other purposes than described
Precautions while at work
• Please ensure that all parts of the machine are firmly
connected before use. Turn the speed button to MINUS, hold
the hand piece firmly and press the on-off button to increase
the speed slowly.
• Never use the machine under the specified Voltage (230V)
• Turn off the machine while changing the tools.
• Keep hands, eyes and face on a safe distance while the machine
is working.
• Turn the machine off immediately when feeling abnormal
movement during operation.
• Do not operate the file when the bit is not locked. It may
damage the hand piece.
• Replace a protective bit after use to prevent troubles.
• Keep moving the bit constantly, don't keep the bit on the
same spot of the nail.
• Please do not press the bit too much while rotating. It does
not only work inefficient but it could also damage the bit
and nail.
• Do not drop the hand piece. If it happens, ensure yourself of
a normal appearance of the tool and bit and then operate
increasing the speed from the [MIN] position gradually. If
something unusual is detected, contact your supplier.
Maintenance and inspection
• Remove dust or dirt with a brush or soft cloth after use. After
that use a moist towel. Dry off with a duster. If there is dirt
on the inside of the collet, remove the collet from the head
and clean it.
• Use dust protectors to prevent dust from damaging your
hand piece.
• Never place a dust protector against the hand piece, leave
some space in between.
• Always remove the bit from the hand piece when you are
finished working. Replace by the protective bit.
• Disinfect your bits according to the guidelines of your
supplier.
• Periodical inspection is recommended every 1 or 2 years for
safe and efficient use. Please consult your service supplier.
Instructions for Kick-Off II Electric File
5
1 3 7
4
2
6
Part identification / connection
1. Power button
2. Speed control knob
3. Rotation switch
4. Hand piece connection
5. Warning light
6. Connection foot controler (option)
7. Fuse
8. Voltage controle (220/110V)
9. Plug AC
1. Connect the hand piece to the machine. (4)
2. If required, connect variable foot controller. (6)
3. Ensure that the power button (1) is turned off before
connecting the AC plug (9) to the power supply.
8
9