Vantage Hearth RadioLink ScenePoint RDR Series Installation

V A N T A G E C O N T R O L S . C O M
1061 South 800 East • Orem, Utah 84097 • Telephone 801 229 2800 • Fax 801 224 0355
Overview
The Vantage RadioLink ScenePoint DR (dual relay) station is a
single gang wall box configuration containing two relays. It
may be ganged with additional ScenePoint Stations up to 4
gangs. It is powered via the local line feed, and communicates
with the system through RadioLink. Before the relay is
programmed, the relays
independent toggle relays or interlocked toggle relays. Once a
button is programmed it can perform any operation a standard
station supports controlling its own or other loads. The
ScenePoint station's relay loads can be controlled by any other
keypad, IR input or timed event. It supports up to six buttons
per station and an optional internal IR receiver. Switch
between interlock and non-interlock operation modes via a
switch located on the back of the station (station is shipped in
interlocked mode).
Specifications
Description
Station Dimensions
Weight
Voltage
5A (600W @ 120V) General Purpose
5A (600W @ 120V) Ballast
Max. Load Each Relay 5A (600W @ 120V) Tungsten
5A (600W @ 120V) Drapery Motor
5A (600W @ 120V) Fluorescent
Minimum Load Required
Incandescent, Cold Cathode, HID,
Load Types
Fluorescent, Constant-Speed Motors
Built-in Lightning / Surge
Protection
Cooling
Status Indicator
Station Equivalent
Station Bus Connections
Ambient Operating
Temperature
Ambient Operating
Humidity
UL and CUL Listed
System Requirements
InFusion Design Center Software must be used to program the
station. The InFusion System must be RadioLink enabled using
the RFE1000 RadioLink Enabler from Vantage.
Installation
Installation of Vantage products should be performed or
supervised by a Certified Vantage Installer. Turn the circuit
breaker off and make sure no voltage is present where the
relay station is to be mounted. Damage caused by failure to
disconnect power may void the warranty and is a risk to the
installer. This station requires Neutral to operate. The Green
ground lead must be connected to the structure's safety
ground.
NOTE: When used as a shade controller only connect one
shade per station. Multiple shades connected to one station
may not stay synchronized and other malfunctions may occur.
THE BLIND'S LIMIT SWITCHES MUST BE SET BEFORE
INSTALLING FOR BLIND CONTROL!
©Vantage, 40597 / IS-0485-A / InFusion
function in default mode
Specification
Height = 4.3" -or- 109mm
Depth = 1.38" -or- 35mm
Width = 2.5" -or- 64mm
4.9oz. -or- 139g
120 ~ 60/50Hz
0 Watts
MOV surge suppression
High Voltage meets IEEE C62.41
(6000V & 3000A)
Low Voltage meets ITU-T K.20
None required
Microprocessor LED Status
1, RadioLink Station
Design Center RadioLink Bus
32 - 77°F -or- 0 - 25°C
5 - 95% non-condensing
Yes
RadioLink ScenePoint DR Station — MODEL: RDR<XXXX>
I N S T A L L A T I O N
RadioLink ScenePoint DR Station — MODEL: RDR<XXXX>
Minimum Back Box Dimensions
For single gang: 2.80"h x 1.80"w x 2.5"d – UL requires one-half
inch clearance between the back of the station to the back of
the back box.
Most standard back boxes that have the receiving threads for
as the dimmer mounting screw inside the box will be adequate.
Most back boxes where the receiving threads are outside the
box will be too small.
In some areas local codes may require that the low voltage
wiring be connected outside of the electrical box. A groove is
provided in the relay station to route the station bus outside of
the electrical box. See detailed drawing at end of instructions.
Mud Rings
If mud rings are specified on a job it is important to test the
mud rings for proper fit. Some mud rings run substantially
smaller than back boxes and are not large enough for the
station. The only solution is to test the fit first.
3-Way Switch Application
A ScenePoint DR Station may be used in any 3-way
application. When installing a ScenePoint DR station, as a 3-
way switch, the Red and Red/White (Loads Out) wires are not
connected and are properly capped-off.
ScenePoint Relay Station Set Up with Design Center
First select the room, then click on Vantage Objects in the
Object Explorer and expand Stations, RadioLink. From the list
of stations double click on the ScenePoint DR Station to place
it in the room. In the Object Editor name the station and make
sure it is on the correct RadioLink station bus port.
Configuration
RadioLink stations need to be configured to associate which
physical station goes with the station in software. When the
station is initially powered-up, the Status LED will blink three
times followed by a pause - this means the station is powered
correctly but not yet on the network. Before uploading the file
to the Vantage system, do the following: From Design Center,
click in the Serial Number section in the Object Editor and type
in the serial number. The serial number of each station is
located on a permanent sticker and a removable sticker on the
front of the station. Remove the sticker with the number only
and place on the Station Design Report for easy reference
when programming. The Main Controller will properly initialize
all the RadioLink stations that it has serial numbers for. This
may take several minutes depending on the number of
RadioLink stations on the network. The Status LED will blink
steadily when a station has been added to the network and
configured.
Operation Modes
Non-Interlocked Mode – SWITCH ON BACK RIGHT POSITION:
This provides two independent relay loads. Each load is
controlled independent of the other load. Two buttons are
selected at final assembly to control the two loads. Typically
button one controls load one and button two controls load
two. The default mode is automatically disabled when the
station is configured.
V A N T A G E I N S T A L L G U I D E S
page 1 of 4