Table of Contents
Advertisement
Quick Links
Submersible Centrifugal Grinder Pump
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notification.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
INSTALLATION MANUAL
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
Series: PGPT
1 HP, 3450 RPM, 60 Hz.
Patent Pending
·
·
·
·
Form No. 140737-Rev. C
Advertisement
Table of Contents
Summary of Contents for CRANE PUMPS & SYSTEMS Barnes PGPT Series
- Page 1 INSTALLATION MANUAL Submersible Centrifugal Grinder Pump Series: PGPT 1 HP, 3450 RPM, 60 Hz. Patent Pending IMPORTANT! Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, · ·...
-
Page 2: Safety First
SAFETY FIRST! Please Read This Before Installing Or Operating Pump. WARNING! - DO NOT pump hazardous materials This information is provided for SAFETY and to PREVENT (flammable, caustic, etc.) unless the pump is specifically EQUIPMENT PROBLEMS. To help recognize this information, designed and designated to handle them. - Page 3 Submersible Centrifugal Grinder Pump USER GUIDE Congratulations on your purchase of a Barnes PGPT grinder pump generates sufficient Grinder Pump. With proper care and by following pressure to pump this slurry from your home a few simple guidelines your grinder pump will to the wastewater plant.
-
Page 4: Pump Specifications
PUMP SPECIFICATIONS: DISCHARGE ....... 1¼” NPT SCH 80, 300 Series SS CORD ENTRY ..... 20ft. (6m) Cord with Plug, CHECK VALVE ....1¼” NPT Cast Iron Custom Molded Quick Connect Style ....Flapper with Integrated Anti-Siphon for Sealing with Strain Relief. LIQUID TEMPERATURE .. - Page 5 MODEL VOLT NEMA FULL LOCKED CORD CODE CORD WINDING START LOAD ROTOR SIZE TYPE O.D. RESISTANCE CODE AMPS AMPS ± .02 (.5) MAIN -- START in (mm) (ohms) PGPT1022 12.5 35.0 14/3 .61 (15.5) 1.5 - 3.3 12.5 35.0 14/3 1.5 - 3.3 PGPT1022A .61 (15.5)
-
Page 6: Installation
RECEIVING/UNPACKING: Upon receiving the pump, it should be inspected for dam- STANDARD "ALARM" age or shortages. If damage has occurred, file a claim POSITION immediately with the company that delivered the pump. Unpack pump and record pump serial and model number 10"... -
Page 7: Cable Connections
Wire Size - If additional cable is required consult a qualified electrician for proper wire size. CABLE CONNECTIONS: Pump Cable- Insert female end of cable plug into housing bore aligning alignment mark with hole in terminal block see Figures 4 & 5. Tighten bolts on compression flange until flush with motor housing. -
Page 8: Wiring Diagram
WIRING DIAGRAM FIGURE 5... -
Page 9: Troubleshooting
TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... - Page 10 EXPLODED VIEW TORQUE TO 11.0 FT. LBS. USE THREAD TORQUE TO LOCKER 11.0 FT. LBS. P/N 030237 TORQUE TO USE THREAD 11.0 FT. LBS. USE LOCKER THREAD LOCKER P/N 030237 P/N 030237 SLIDE CAPACITOR 4X TORQUE TO OUT OF ZIPTIES THEN 2 IN.
-
Page 11: Parts List
PARTS LIST Seal/Overhaul Kit ....p/n 138085A Cutter Kit ....... p/n 138086A Shim Kit ......... p/n 138087A ITEM PART NO. DESCRITION 136566CT Casing, CI 136574 Elbow,Discharge,CI,1.25 136561 Cutter,Radial,SS,2.015” 136564 Ring,Shred,SS,2.023” 110328 Housing, Motor, Single (AU) 108342 Housing, Motor, SIngle, (MAN) 136571B-LB Plate, Seal, Cast Iron 136569... - Page 12 Notes...
- Page 13 Limited 24 Month Warranty Crane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained in accordance with our instructions.This warranty gives you specifi c legal rights, and there may also be other rights which vary from state to state.
-
Page 14: Returned Goods
IMPORTANT! WARRANTY REGISTRATION Your product is covered by the enclosed Warranty. If you have a claim under the provision of the warranty, contact your local Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”. CONTACT YOUR LOCAL CRANE PUMPS &... - Page 15 A Crane Co. Company START-UP REPORT General Information Pump Owner’s Name: __________________________________________________________ Address: ____________________________________________________________________ Location of Installation: _________________________________________________________ Contact Person: __________________________________Phone: _______________________ Purchased From: _____________________________________________________________ Nameplate Data Pump Model #: ___________________ Serial #: _____________________________________ Part #: __________________________ Impeller Diameter: ____________________________ Voltage: _________ Phase: _____ Ø...
- Page 16 Submersible Pumps Resistance of cable and pump motor (measured at pump control): Red-Black:_______Ohms(Ω) Red-White:_______Ohms(Ω) White-Black:_______Ohms(Ω) Resistance of Ground Circuit between Control Panel and outside of pump: __________Ohms(Ω) MEG Ohms check of insulation: Red to Ground: _________ White to Ground: __________ Black to Ground: ____________ Operational Checks Is there noise or vibration present? YES___ NO___ Source of noise/vibration: ___________...
Need help?
Do you have a question about the Barnes PGPT Series and is the answer not in the manual?
Questions and answers