Advertisement
fig 1
4.
OPERATING INSTRUCTIONS
Note: Numbers in brackets refer to item numbers in the parts list.
The air hammer is designed primarily for use on vehicle bodywork. We do not recommend any other use. Ensure you read, understand and follow the safety
instructions in Section 1.
4.1
Attach the retaining spring (20) by screwing it onto the cylinder (18).
4.2
Insert the chisel using the hooked end of the spring to hold the chisel in place.
4.3
Attached the tool to the air supply (see Section 3).
4.4
To operate the hammer, squeeze the trigger (11).
5.
MAINTENANCE
WARNING! Disconnect the hammer from the air supply before changing chisels, servicing or performing any maintenance.
p
Keep the hammer oiled for optimum performance. Lubricate with a good grade of air tool oil such as Sealey ATO/500 or ATO/1000. If there is no oiler in
5.1
the air system then a teaspoon of oil can be poured into the air inlet of the hammer, or into the hose at the nearest connection to the air supply. Then run
the hammer for a short time.
Note: The following external factors may cause loss of power and effect hammer performance:
The air supply: reduced compressor output, excessive drain on the air line, moisture or restrictions in air pipes or the use of hose connectors having too small a bore.
Correct as necessary.
The hammer: grit or gum deposits in the tool. Correct by cleaning the air strainer and flushing out the tool with gum solvent oil or an equal mixture of SAE No.10
oil and kerosene. If, despite taking action as above, the tool function is still impaired, contact your local Sealey service agent.
6.
PARTS LIST
ITEM
PART NO.
DESCRIPTION
01.
GSA11.01
HOUSING
02.
GSA01.05
SPRING PIN
03.
GSA01.08
VALVE SEAT
04.
GSA01.09
THROTTLE VALVE
05.
GSA11.05
VALVE SPRING
06.
GSA11.06
EXHAUST DEFLECTOR
07.
GSA01.12
AIR INLET
08.
GSA11.08
PLASTIC GRIP
09.
GSA11.09
BUSHING
10.
GSA11.10
TRIGGER SHAFT
11.
GSA01.06
TRIGGER
12.
GSA11.12
REAR VALVE SEAT
13.
GSA11.13
CHECK VALVE
14.
GSA11.14
VALVE PIN (A)
15.
GSA11.15
PIN
16.
GSA11.16
UPPER VALVE
17.
GSA11.17
PISTON
18.
GSA12.18
ROUND CYLINDER
19.
GSA11.19
PLASTIC COVER
20.
GSA11.20
SPRING RETAINER
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12 months from
purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on
01284 757525 and leave your full name and address, including postcode.
Declaration of Conformity
MEDIUM STROKE G3 AIR HAMMER
Model: GSA12
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
01284 757500
We, the sole importer into the UK, declare that the product listed here is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a
national authority, upon request to Jack Sealey Ltd.
Signed by Mark Sweetman
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 703534
24th November 2004
www.sealey.co.uk
Web
fig 2
Issue No:
Issue Date:
For Jack Sealey Ltd.
Sole importer into the UK
of Sealey Power Products
sales@sealey.co.uk
email
GSA12 - 1 - 241104
1
241104
Advertisement
