Page 1: Table Of Contents
 Installation  Starting the Application  Report tab  Settings tab  Synchronising the clock  Administrator settings  Info tab  Update… tab AT-100 device  Installing batteries  Mounting the AT-100  Alarms and indicators V0.2 Page 1...
Page 2: Safety And Regulatory Information
AT-100 by unauthorised, unfamiliar or untrained users could result in death or serious injury. The service life of the AT-100 depends in part on how it is used and the environmental conditions in which it is used. Under heavy usage, or under extreme environmental conditions, the service life of the equipment may be reduced.
Page 3: Regulatory Compliance
 European Union WEEE and battery directives: When the AT-100 reaches the end of its useful life, dispose of it at an appropriate collection point. Do not dispose of it in the normal domestic waste stream. When the batteries reach the end of their useful life, dispose of them at an appropriate collection point.
Page 4: Please Read This First
PLEASE READ THIS FIRST Before first use of your AT-100, please initialise your device to your local time zone. See page 9, “Synchronising the clock” for details. V0.2 Page 4...
Page 5: Pc Application
Starting the Application To start, first connect your AT-100 to a spare USB port on your computer using the USB cable provided. Unscrew the battery cap to expose the USB port in the device. Remove the batteries and connect the USB cable. The front of the device will illuminate in green to indicate USB is connected.
Page 6: Report Tab
Left click “OK” when a message box appears showing “Data download complete”. The AT-100 records data in 2-minute blocks. Please note that in its default configuration, 2-minute data blocks are only recorded if they contain at least one temperature record exceeding the active threshold.
Page 7 You can zoom in to select any particular region of interest on the chart. Move the cursor into the chart area and position it over the start or end of the region you wish to inspect. Click and hold the left mouse button, drag the cursor to the other end of the region of interest, and release the left mouse button.
Page 8 Again, you can zoom in on the chart to select an area of interest by dragging the cursor as before. A horizontal scroll bar will appear with a button to the left. You can use the scroll bar to inspect other areas of the chart.
Page 9: Settings Tab
To synchronise the AT-100 clock to the current date and time settings on your computer, select the “Sync AT-100 Clock” button. This will send the current data and time settings to the AT-100, and initialise it to those settings. Its date and time will then appear in the boxes labelled “AT-100 Clock”. Administrator settings To access the Administrator settings, enter the Administrator password in the “Enter password”...
Page 10 To check the contents of the AT-100 at any time, select the “Get Current AT-100 Settings” button. This will update the grey “Current Settings” boxes from the device. This operation is performed automatically after successfully entering the Administrator password. To update any of the user or threshold settings, enter the new text or values in the white “New Settings”...
Page 11: Info Tab
Info tab Selecting the “Go To Website” button will open a Web browser window to the Dynamic Micro Systems website, where you can browse and download product information and obtain contact details. V0.2 Page 11...
Page 12: Update
Update… tab The update feature is not implemented yet, as no updates are available. V0.2 Page 12...
Page 13: At-100 Device
For bracket selection and fitment, please refer to the instructions accompanying the bracket kit. Once the bracket is attached to the helmet, insert the AT-100 from the rear. Adjust its position and orientation so that the front LED is visible in the user’s peripheral vision. Once the positioning is correct, secure the unit in place by tightening the retaining grubscrew with the Allen key provided.
Page 14: Alarms And Indicators
Alarms and indicators The AT-100 has a number of operating modes depending on temperature. Additionally, the device can be configured to record temperature data continuously when on battery power, or (factory setting) only when the temperature exceeds the active threshold during the current 2-minute recording block (see “Administrator settings”...